Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0516  Battery Temperature Sensor Circuit Low  P0517  Battery Temperature Sensor Circuit High  


DESCRIPTION

A110648E14
1.438,2.438 1.438,1.958 1.438,1.958 0.49,1.958 false 0.042,0.271 1.406,0.49 1.365,0.219 10 false Resistance (kΩ) 0.302,0.771 0.448,0.969 0.146,0.198 10 false 6 0.302,1.75 0.448,1.948 0.146,0.198 10 false 2 0.302,2 0.448,2.198 0.146,0.198 10 false 1 0.302,1.51 0.448,1.708 0.146,0.198 10 false 3 0.302,1.25 0.448,1.448 0.146,0.198 10 false 4 0.302,1.01 0.448,1.208 0.146,0.198 10 false 5 0.302,2.26 0.448,2.458 0.146,0.198 10 false 0 0.781,2.469 1,2.667 0.219,0.198 10 false 10 1.167,2.479 1.385,2.677 0.219,0.198 10 false 20 1.958,2.49 2.177,2.688 0.219,0.198 10 false 40 2.354,2.479 2.573,2.677 0.219,0.198 10 false 50 2.729,2.479 2.948,2.677 0.219,0.198 10 false 60 1.552,2.479 1.771,2.677 0.219,0.198 10 false 30 0.74,2.729 1.115,2.927 0.375,0.198 10 false (50) 1.125,2.729 1.5,2.927 0.375,0.198 10 false (68) 2.667,2.698 3.094,2.896 0.427,0.198 10 false (140) 2.271,2.719 2.74,2.917 0.469,0.198 10 false (122) 1.854,2.729 2.302,2.927 0.448,0.198 10 false (104) 1.51,2.729 1.885,2.927 0.375,0.198 10 false (86) 2.552,2.969 3.354,3.167 0.802,0.198 10 false °C (°F)

The battery temperature sensor installed on the battery current sensor detects battery temperature.

A thermistor is integrated into the battery temperature sensor, and the resistance in the battery temperature sensor changes according to the battery temperature.

The resistance of the thermistor in the battery temperature sensor decreases as the battery temperature increases. The resistance increases as the temperature decreases.

The battery temperature sensor is connected to the ECM. The ECM supplies 5 V from the THB terminal to the battery temperature sensor through resistor R.

The battery temperature sensor and resistor R are connected in series. This results in fluctuations in the voltage supplied from the THB terminal when the resistance changes according to the battery temperature.

The ECM determines the battery temperature according to fluctuations in voltage. When the battery temperature is high, the ECM determines to reduce the amount of current supplied from the generator in order to protect the battery.

DTC No. DTC Detection Condition Trouble Area
P0516 Battery temperature sensor output value is 0.2 V or less for 0.5 seconds or more with the engine switch on (IG) (1 trip detection logic).
·

Battery temperature sensor

·

Short in battery temperature sensor circuit

·

ECM


P0517 Battery temperature sensor output value is 4.8 V or more for 0.5 seconds or more with the engine switch on (IG) (1 trip detection logic).
·

Battery temperature sensor

·

Open in battery temperature sensor circuit

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT BATTERY CURRENT SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)

NG

REPLACE BATTERY CURRENT SENSOR

2.CHECK HARNESS AND CONNECTOR (BATTERY CURRENT SENSOR - ECM)
a.

Disconnect the battery current sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A2-1 (THB) - D1-103 (THB) Always Below 1 Ω
A2-4 (E2) - D1-101 (EIB) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A2-1 (THB) or D1-103 (THB) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR