Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A384173E06
2.542,4.625 2.813,4.271 2.813,4.271 4.25,4.271 false 3.74,5.115 3.344,5.115 3.344,5.115 3.156,4.813 false 0.135,0.104 1.188,0.49 1.052,0.385 10 false VVT System: 0.177,2.646 0.979,3.021 0.802,0.375 10 false Duty-cycle 1.604,3.802 4.427,4.156 2.823,0.354 10 false Camshaft Timing Oil Control Valve Assembly 0.323,4.313 1.719,4.698 1.396,0.385 10 false Engine Oil Pressure 4.333,4.198 6.354,4.781 2.021,0.583 10 false VVT Controller (Camshaft Timing Exhaust Gear Assembly) 3.802,5.01 5.344,5.385 1.542,0.375 10 false Exhaust Camshaft 5.146,0.875 6.333,1.281 1.188,0.406 10 false VVT Sensor 4.688,1.406 6.573,1.729 1.885,0.323 10 false Crankshaft Position Sensor 4.51,1.906 6.823,2.219 2.313,0.313 10 false Mass Air Flow Meter Sub-assembly 4.823,2.406 6.563,2.792 1.74,0.385 10 false Throttle Position Sensor 4.49,2.917 6.802,3.188 2.313,0.271 10 false Engine Coolant Temperature Sensor 4.885,3.406 6.51,3.771 1.625,0.365 10 false Vehicle Speed Sensor 2.365,1.271 3.656,1.656 1.292,0.385 10 false Actual Valve Timing 2.354,2.021 3.74,2.396 1.385,0.375 10 false Target Valve Timing 2.646,2.729 3.448,3.104 0.802,0.375 10 false Correction 2.865,3.563 3.667,3.938 0.802,0.375 10 false ECM

DTC No. DTC Detection Condition Trouble Area
P0013 Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 1) circuit

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1)

·

ECM


P0023 Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for exhaust camshaft of bank 2) circuit

·

Camshaft timing oil control valve assembly (for exhaust camshaft of bank 2)

·

ECM



WIRING DIAGRAM

A255389E07
0.474,1.617 0.963,1.773 0.489,0.156 10 D46 0.474,1.767 3.296,2.103 2.823,0.336 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft of Bank 1) 0.474,3.595 1.088,3.751 0.614,0.156 10 D33 0.474,3.745 3.315,4.081 2.841,0.336 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft of Bank 2) 5.174,0.477 5.439,0.637 0.265,0.161 10 16 5.174,1.232 5.349,1.393 0.175,0.161 10 17 5.174,2.442 5.349,2.602 0.175,0.161 10 14 5.174,3.198 5.349,3.359 0.175,0.161 10 15 5.422,0.468 5.842,0.665 0.420,0.196 10 OE1+ 5.422,1.226 5.842,1.423 0.420,0.196 10 OE1- 5.422,2.442 5.842,2.638 0.420,0.196 10 OE2+ 5.422,3.19 5.842,3.386 0.420,0.196 10 OE2- 6.006,4.087 6.338,4.283 0.332,0.196 10 ECM 5.758,4.087 6.066,4.283 0.308,0.196 10 D1 1.456,0.482 1.631,0.642 0.175,0.161 10 1 1.456,1.209 1.631,1.369 0.175,0.161 10 2 1.455,2.442 1.630,2.602 0.175,0.161 10 1 1.455,3.182 1.630,3.342 0.175,0.161 10 2

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is output, check the VVT system (for exhaust camshaft of bank 1) circuit.

·

If DTC P0023 is output, check the VVT system (for exhaust camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).



PROCEDURE

1.READ OUTPUT DTC (P0013 OR P0023)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Clear the DTC after recording the freeze frame data and DTC (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).


e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG) and wait 5 seconds.


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Result
Result Proceed to
DTC P0013 or P0023 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D1-16 (OE1+) - D46-1 Always Below 1 Ω
D1-17 (OE1-) - D46-2 Always Below 1 Ω
D1-14 (OE2+) - D33-1 Always Below 1 Ω
D1-15 (OE2-) - D33-2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D1-16 (OE1+) or D46-1 - Body ground Always 10 kΩ or higher
D1-17 (OE1-) or D46-2 - Body ground Always 10 kΩ or higher
D1-14 (OE2+) or D33-1 - Body ground Always 10 kΩ or higher
D1-15 (OE2-) or D33-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR