Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The VVT sensor (for exhaust camshaft) (EV1, EV2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The exhaust camshaft has a timing rotor for the VVT sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and the Variable Valve Timing (VVT) system.

DTC No. DTC Detection Condition Trouble Area
P0365
P0390
·

Input voltage to ECM remains 0.3 V or less, or 4.7 V or higher for more than 5 seconds, when 2 or more seconds have elapsed after turning engine switch on (IG)

(1 trip detection logic)

·

No VVT sensor signal to ECM during cranking

(1 trip detection logic)


·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

Exhaust camshaft

·

Valve timing

·

ECM


P0367
P0392
The output voltage of the exhaust VVT sensor (bank 1, 2) is less than 0.3 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

ECM


P0368
P0393
The output voltage of the exhaust VVT sensor (bank 1, 2) is higher than 4.7 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust camshaft) circuit

·

VVT sensor (for exhaust camshaft)

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
a.
U188249E02
1.979,2.135 2.635,2.594 false 0.125,0.063 1.438,0.24 1.313,0.177 10 false Wire Harness Side: 0.323,1.552 0.594,1.729 0.271,0.177 10 false D44 0.208,1.792 0.719,1.99 0.51,0.198 10 false Bank 1 0.323,2.073 0.604,2.25 0.281,0.177 10 false D31 0.208,2.323 0.729,2.521 0.521,0.198 10 false Bank 2 1.219,1.042 2.042,1.24 0.823,0.198 10 false VVT Sensor 1.313,2.771 2.01,2.969 0.698,0.198 10 false Front View 2.635,2.594 2.948,2.792 0.313,0.198 10 false VC2

Disconnect the VVT sensor (for exhaust camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
D44-3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.5 V
D31-3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.5 V




OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHASUT CAMSHAFT) -ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D44-1 (EX+) - D1-68 (EV1+) Always Below 1 Ω
D44-2 (EX-) - D1-91 (EV1-) Always Below 1 Ω
D31-1 (EX+) - D1-66 (EV2+) Always Below 1 Ω
D31-2 (EX-) - D1-89 (EV2-) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D44-1 (EX+) or D1-68 (EV1+) - Body ground Always 10 kΩ or higher
D44-2 (EX-) or D1-91 (EV1-) - Body ground Always 10 kΩ or higher
D31-1 (EX+) or D1-66 (EV2+) - Body ground Always 10 kΩ or higher
D31-2 (EX-) or D1-89 (EV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR INSTALLATION)
a.
B319222E16
1.365,1.563 2.031,1.792 0.667,0.229 10 false Clearance 0.406,1.771 0.927,1.958 0.521,0.188 10 false Normal 2.469,1.781 3.146,1.969 0.677,0.188 10 false Abnormal

Check the VVT sensor installation condition.

OK:

Sensor is installed correctly.




OK

4.CHECK EXHAUST CAMSHAFT

NG

4.CHECK EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.




OK

5.CHECK VALVE TIMING

NG

5.CHECK VALVE TIMING

OK

6.REPLACE VVT SENSOR

NG

ADJUST VALVE TIMING

6.REPLACE VVT SENSOR

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine / DTC.


i.

Read the DTCs.

Result
Result Proceed to
DTC P0365, P0367, P0368, P0390, P0392 or P0393 is output A
DTC is not output B

HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR EXHASUT CAMSHAFT) -ECM)
a.

Disconnect the VVT sensor (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):
Tester Connection Condition Specified Condition
D44-3 (VC2) - D1-114 (VCE1) Always Below 1 Ω
D31-3 (VC2) - D1-112 (VCE2) Always Below 1 Ω


Standard resistance (Check for short):
Tester Connection Condition Specified Condition
D44-3 (VC2) or D1-114 (VCE1) - Body ground Always 10 kΩ or higher
D31-3 (VC2) or D1-112 (VCE2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR