Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059540 2GR-FE ENGINE CONTROL _0291770 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  P0021  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)  P0022  Camshaft Position "A" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

Refer to DTC P0010 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0010).

DTC No. DTC Detection Condition Trouble Area
P0011
P0021
Advanced cam timing:
With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (1 trip detection logic):
1. Difference between target and actual intake valve timing is more than 5°CA (Crankshaft Angle) for 4.5 seconds
2. Current intake valve timing is fixed (timing changes less than 5°CA in 5 seconds)
3. Variations in VVT controller timing is more than 19°CA of maximum delayed timing (advance)
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank1, 2)

·

Oil control valve filter (RH, LH)

·

Oil pipe

·

Camshaft timing gear assembly (bank1, 2)

·

ECM


P0012
P0022
Retarded cam timing:
With engine warmed up and engine speed of between 500 rpm and 4000 rpm, all conditions (1), (2) and (3) are met (2 trip detection logic):
1. Difference between target and actual intake valve timing is more than 5°CA (Crankshaft Angle) for 4.5 seconds
2. Current intake valve timing is fixed (timing changes less than 5°CA in 5 seconds)
3. Variations in VVT controller timing is 19°CA or less of maximum delayed timing (retarded)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
Abnormal bank Advanced timing over
(Valve timing is out of specified range)
Retarded timing over
(Valve timing is out of specified range)
Bank 1 P0011 P0012
Bank 2 P0021 P0022

·

If DTC P0011 or P0012 is output, check the VVT system (for intake camshaft of bank 1) circuit.

·

If DTC P0021 or P0022 is output, check the VVT system (for intake camshaft of bank 2) circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.

·

Read freeze frame data using an intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0011, P0012, P0021 or P0022 is output A
DTC P0011, P0012, P0021 or P0022 and other DTCs are output B

HINT:

If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Turn the A/C switch on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).


f.

Check the engine speed while operating the camshaft timing oil control valve assembly (for intake camshaft) using the tester.

OK
Tester Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls

HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2] (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Clear the DTCs.


d.

Start the engine and warm it up.


e.

Drive the vehicle for more than 10 minutes.


f.

Enter the following menus: Powertrain / Engine / DTC / Pending.


g.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0011, P0012, P0021 or P0022 is output B

HINT:

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.




A

B

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
a.

Remove the cylinder head cover sub-assembly RH and LH.

A373786E05
4,0.948 4.198,0.469 4.198,0.469 4.01,1.167 false 4.802,0.979 4.49,1.552 4.49,1.552 4.781,1.26 false 4.083,2.646 4.281,2.26 4.281,2.26 4.083,3 false 4.813,2.729 4.5,3.302 4.5,3.302 4.854,2.906 false 4.51,3.292 4.813,2.906 false 4.146,0.281 5.01,0.51 0.865,0.229 10 false Timing Mark 3.927,1.573 4.792,1.802 0.865,0.229 10 false Timing Mark 4.208,2.063 5.073,2.292 0.865,0.229 10 false Timing Mark 3.917,3.344 4.781,3.573 0.865,0.229 10 false Timing Mark


b.

Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned with the timing marks of the bearing cap as shown in the illustration.

If not, turn the crankshaft 1 revolution (360°), then align the marks as above.

OK:

Timing marks on the camshaft timing gear assemblies and camshaft timing exhaust gear assemblies are aligned as shown in the illustration.




OK

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft) (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
a.
G102538E01
0.104,0.073 1.333,0.271 1.229,0.198 10 false RH Bank: 0.104,2.417 1.208,2.719 1.104,0.302 10 true LH Bank:

Remove the oil pipe or No. 1 or oil pipe.


b.

Remove the oil control valve filter RH or oil control valve filter LH.


c.

Check that the oil control valve filter and oil pipe are not clogged.

OK:

The oil control valve filter and oil pipe are not clogged.




OK

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE CAMSHAFT)

NG

REPLACE OIL CONTROL VALVE FILTER OR PIPE

7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Replace the camshaft timing gear assembly (bank 1 or bank 2) (See page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Start the engine and warm it up.


f.

Drive the vehicle for more than 10 minutes.


g.

Enter the following menus: Powertrain / Engine / DTC / Pending.


h.

Read the pending DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0011, P0012, P0021 or P0022 is output B



A

END

B