Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM J

2AZ-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the starter relay drive signal output from the STAR terminal of the ECM is input into the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. Thus, the ECM interprets that the engine is cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.

While the NE signal is input into the ECM when the engine is running, the ECM turns the Tr1 on continuously.

A218264E06
2.396,0.492 2.765,0.639 0.369,0.147 10 IG2D 1.668,0.935 2.685,1.093 1.017,0.158 10 Main Body ECU 1.223,1.852 1.477,1.994 0.253,0.142 10 IG2 2.842,2.295 3.095,2.437 0.253,0.142 10 IG2 1.223,2.98 1.470,3.129 0.246,0.149 10 EFI 2.625,3.443 3.246,3.598 0.621,0.156 10 EFI MAIN 0.656,4.872 1.298,5.041 0.642,0.170 10 F/B BATT 0.649,6.133 1.222,6.288 0.573,0.156 10 FL MAIN 0.754,7.008 1.229,7.178 0.475,0.170 10 Battery 2.078,6.994 2.776,7.136 0.698,0.142 10 Fuel Pump 3.199,5.054 3.667,5.196 0.468,0.142 10 C/OPN 4.628,4.031 4.909,4.180 0.281,0.149 10 IGN 5.875,1.719 6.073,1.868 0.198,0.149 10 +B 5.875,2.28 6.149,2.422 0.274,0.142 10 +B2 5.871,3.176 6.284,3.332 0.413,0.156 10 MREL 5.889,5.313 6.107,5.469 0.218,0.156 10 FC 5.875,6.441 6.163,6.597 0.288,0.156 10 STA 5.875,6.938 6.184,7.094 0.309,0.156 10 NE+ 5.882,7.646 6.093,7.802 0.211,0.156 10 E1 4.466,6.514 5.413,6.684 0.948,0.170 10 from ST Relay 3.832,7.004 5.383,7.340 1.552,0.336 10 from Crankshaft Position Sensor (NE Signal) 6.197,8.42 6.548,8.562 0.350,0.142 10 ECM 6.435,5.411 6.668,5.567 0.232,0.156 10 Tr1

WIRING DIAGRAM

A218265E07
2.406,0.458 2.771,0.604 0.365,0.146 10 false IG2D 2.802,0.469 3.094,0.615 0.292,0.146 10 false G58 2.875,0.271 3.063,0.406 0.188,0.135 10 false 11 1.667,0.917 2.688,1.083 1.021,0.167 10 false Main Body ECU 1.229,1.823 1.49,1.979 0.26,0.156 10 false IG2 2.813,2.292 3.073,2.448 0.26,0.156 10 false IG2 1.208,2.958 1.479,3.125 0.271,0.167 10 false EFI 3.25,1.583 3.365,1.729 0.115,0.146 10 false 3 2.521,1.583 2.635,1.729 0.115,0.146 10 false 5 2.521,1.906 2.635,2.052 0.115,0.146 10 false 2 3.24,1.906 3.354,2.052 0.115,0.146 10 false 1 3.25,2.719 3.365,2.865 0.115,0.146 10 false 3 2.521,2.719 2.635,2.865 0.115,0.146 10 false 5 2.521,3.063 2.635,3.208 0.115,0.146 10 false 2 3.24,3.063 3.354,3.208 0.115,0.146 10 false 1 3.042,4.333 3.156,4.479 0.115,0.146 10 false 3 3.76,4.333 3.875,4.479 0.115,0.146 10 false 5 3.042,4.646 3.156,4.792 0.115,0.146 10 false 2 3.76,4.646 3.875,4.792 0.115,0.146 10 false 1 2.615,3.448 3.24,3.604 0.625,0.156 10 false EFI MAIN 3.188,5.021 3.667,5.188 0.479,0.167 10 false C/OPN 4.625,4 4.906,4.24 0.281,0.24 10 false IGN 0.667,4.854 1.313,5.021 0.646,0.167 10 false F/B BATT 0.646,6.104 1.219,6.271 0.573,0.167 10 false FL MAIN 0.75,6.958 1.229,7.125 0.479,0.167 10 false Battery 1.979,6.688 2.094,6.844 0.115,0.156 10 false 4 1.969,7.24 2.083,7.396 0.115,0.156 10 false 5 2.104,6.979 2.802,7.156 0.698,0.177 10 false Fuel Pump 2.104,6.813 2.469,6.979 0.365,0.167 10 false M17 5.615,1.479 5.74,1.646 0.125,0.167 10 false 2 5.625,2.031 5.75,2.198 0.125,0.167 10 false 1 5.625,5.208 5.75,5.375 0.125,0.167 10 false 7 5.521,7 5.813,7.167 0.292,0.167 10 false 104 5.573,2.938 5.771,3.104 0.198,0.167 10 false 44 5.573,1.698 5.76,1.833 0.188,0.135 10 false A7 5.583,2.26 5.771,2.396 0.188,0.135 10 false A7 5.573,3.146 5.76,3.281 0.188,0.135 10 false A7 5.573,5.427 5.76,5.563 0.188,0.135 10 false A7 5.552,7.188 5.76,7.365 0.208,0.177 10 false D2 5.885,1.688 6.135,1.896 0.25,0.208 10 false +B 5.885,2.24 6.167,2.49 0.281,0.25 10 false +B2 5.885,3.156 6.344,3.427 0.458,0.271 10 false MREL 5.885,5.302 6.115,5.458 0.229,0.156 10 false FC 5.885,7.188 6.24,7.344 0.354,0.156 10 false E1 6.167,8.156 6.5,8.333 0.333,0.177 10 false ECM 6.563,5.365 6.865,5.531 0.302,0.167 10 false Tr1

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


d.

Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.

OK:

Fuel pump operating sound occurs.




NG

2.CHECK C/OPN RELAY INPUT VOLTAGE

OK

8.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.CHECK C/OPN RELAY INPUT VOLTAGE
a.
A135435E01
0.576,0.542 2.586,0.708 2.010,0.166 10 Engine Room No. 1 Relay Block 0.178,2.009 1.062,2.339 0.883,0.330 10 C/OPN Relay Holder

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Measure the voltage of the engine room No. 1 relay block terminals when the engine switch is turned on (IG) and off.

Standard Voltage:
Tester Connection Engine Switch Condition Specified Condition
C/OPN relay terminal (5) - Body ground off Below 1 V
C/OPN relay terminal (1) - Body ground
C/OPN relay terminal (5) - Body ground on (IG) 11 to 14 V
C/OPN relay terminal (1) - Body ground




NG

3.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI MAIN RELAY, IG2 RELAY)

OK

4.INSPECT C/OPN RELAY
3.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - EFI MAIN RELAY, IG2 RELAY)
a.

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Remove the EFI MAIN relay from the engine room No. 1 relay block.


c.

Remove the IG2 relay from the engine room No. 1 relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPN relay terminal (5) - Relay block EFI MAIN relay terminal (3) Always Below 1 Ω
C/OPN relay terminal (1) - Relay block IG2 relay terminal (3) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT C/OPN RELAY
a.
B016200

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)




OK

5.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)

NG

REPLACE C/OPN RELAY

5.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)
a.

Remove the C/OPN relay from the engine room No. 1 relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPN relay terminal (2) - A7-7 (FC) Always Below 1Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C/OPN relay terminal (2) or A7-7 (FC) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP - BODY GROUND)
a.

Check the harness and the connectors between the C/OPN relay and the fuel pump.

i.

Remove the C/OPN relay from the engine room No. 1 relay block.


ii.

Disconnect the fuel pump connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C/OPN relay terminal (3) - M17-4 Always Below 1Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C/OPN relay terminal (3) or M17-4 - Body ground Always 10 kΩ or higher




b.

Check the harness and the connectors between the fuel pump and the body ground.

i.

Disconnect the fuel pump connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
M17-5 - Body ground Always Below 1 Ω





OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.


OK

NG

8.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the result when the engine switch is turned on (IG) and START.

OK:
Engine Switch Position Starter Signal
On (IG) Open*1
ON*2
START Close*1
OFF*2


*1: for CVT models.

*2: for A/T models.




OK

9.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

REPAIR OR REPLACE STARTING SYSTEM

9.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


d.

Read the values displayed on the tester while cranking.

OK:

Values are displayed continuously.




OK

REPLACE ECM

NG

REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT