When the engine is cranked, the starter relay drive signal output from the STAR terminal of the ECM is input into the STA terminal of the ECM, and NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. Thus, the ECM interprets that the engine is cranked, and turns the transistor Tr1 in the ECM internal circuit ON. The current flows to the C/OPN (Circuit Opening) relay by turning the Tr1 ON. Then, the fuel pump operates.
While the NE signal is input into the ECM when the engine is running, the ECM turns the Tr1 on continuously.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.
Fuel pump operating sound occurs.
NG
OK
Remove the C/OPN relay from the engine room No. 1 relay block.
Measure the voltage of the engine room No. 1 relay block terminals when the engine switch is turned on (IG) and off.
| Tester Connection | Engine Switch Condition | Specified Condition |
|---|---|---|
| C/OPN relay terminal (5) - Body ground | off | Below 1 V |
| C/OPN relay terminal (1) - Body ground | ||
| C/OPN relay terminal (5) - Body ground | on (IG) | 11 to 14 V |
| C/OPN relay terminal (1) - Body ground |
NG
OK
Remove the C/OPN relay from the engine room No. 1 relay block.
Remove the EFI MAIN relay from the engine room No. 1 relay block.
Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C/OPN relay terminal (5) - Relay block EFI MAIN relay terminal (3) | Always | Below 1 Ω |
| C/OPN relay terminal (1) - Relay block IG2 relay terminal (3) | Always | Below 1 Ω |
OK
NG
Remove the C/OPN relay from the engine room No. 1 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
|---|---|
| 3 - 5 | 10 kΩ or higher |
| Below 1 Ω
(when battery voltage is applied to terminals 1 and 2) |
OK
NG
Remove the C/OPN relay from the engine room No. 1 relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C/OPN relay terminal (2) - A7-7 (FC) | Always | Below 1Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C/OPN relay terminal (2) or A7-7 (FC) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the harness and the connectors between the C/OPN relay and the fuel pump.
Remove the C/OPN relay from the engine room No. 1 relay block.
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C/OPN relay terminal (3) - M17-4 | Always | Below 1Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C/OPN relay terminal (3) or M17-4 - Body ground | Always | 10 kΩ or higher |
Check the harness and the connectors between the fuel pump and the body ground.
Disconnect the fuel pump connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M17-5 - Body ground | Always | Below 1 Ω |
OK
NG
Inspect the fuel pump (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL PUMP>INSPECTION).
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Check the result when the engine switch is turned on (IG) and START.
| Engine Switch Position | Starter Signal |
|---|---|
| On (IG) | ON |
| START | OFF |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Read the values displayed on the GTS while cranking.
Values are displayed continuously.
OK
NG