The Crankshaft Position (CKP) sensor system consists of a crankshaft position sensor plate and a pickup coil.
The crankshaft position sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crankshaft position sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0335 | One of the following conditions is met (1 trip detection logic):
·
No crankshaft position sensor signal to ECM while cranking ·
No crankshaft position sensor signal to ECM while engine running ·
Missing crankshaft position sensor signal despite camshaft position sensor signal inputs normal after engine cranked |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft position sensor plate ·
ECM |
| P0339 | All of the following conditions are met (1 trip detection logic):
(a) The engine speed is 1000 rpm or higher. (b) No crankshaft position sensor signal for 0.05 seconds or more. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft position sensor plate ·
ECM |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
G2 stands for the Camshaft Position (CMP) sensor signal, and NE stands for the CKP sensor signal.
Grounding failure of the shielded wire may cause noise in waveforms.
| Item | Content |
|---|---|
| Symbols (Terminal No.) | CH1: D2-99 (G2+) - D2-98 (G2-)
CH2: D2-122 (NE+) - D2-121 (NE-) |
| Tool Setting | 5 V/DIV.
20 msec./DIV. |
| Condition | Idling |
After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
Installation condition of the camshaft position sensor
Installation condition of the camshaft
Connection of the camshaft position sensor connector
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.
The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
Start the engine.
Read the values displayed on the tester while the engine is running.
Correct values are displayed.
To check the engine speed change, display the graph on the tester.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the tester remains zero (0), there may be an open or short in the crankshaft position sensor circuit.
NG
OK
Inspect the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>INSPECTION).
OK
NG
Disconnect the CKP sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D54-1 - D2-122 (NE+) | Always | Below 1 Ω |
| D54-2 - D2-121 (NE-) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D54-1 or D2-122 (NE+) - Body ground | Always | 10 kΩ or higher |
| D54-2 or D2-121 (NE-) - Body ground |
OK
NG
Check the CKP sensor installation.
Sensor is installed correctly.
OK
NG
Check the teeth of the sensor plate.
Sensor plate does not have any cracks or deformation.
OK
NG
Replace the crankshaft position sensor (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Clear DTCs (see page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Display (DTC output) | Proceed to |
|---|---|
| No output | A |
| P0335 or P0339 | B |
If the engine does not start, replace the ECM.
A
B