Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.


The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is a planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A107164E62
1.646,2.385 1.938,2.385 false 1.479,2.396 0.938,2.135 false 2.938,2.354 3.417,2.677 false 2.75,2.177 3.406,2.365 false 2.802,1.771 3.354,1.698 false 3.094,1.594 3.417,1.417 false 2.896,2.115 3.406,2.365 false 2.958,1.594 3.385,1.135 false 1.115,2.896 1.24,3.094 0.125,0.198 10 false A 1.792,2.896 1.917,3.094 0.125,0.198 10 false A 0.385,1.979 1,2.198 0.615,0.219 10 false Element 0.052,2.719 0.979,2.938 0.927,0.219 10 false Exhaust Gas 2.573,2.969 3.792,3.188 1.219,0.219 10 false A-A Cross Section 3.427,2.281 4.854,2.5 1.427,0.219 10 false Platinum Electrode 1.969,2.292 2.531,2.51 0.563,0.219 10 false Cover 3.427,2.677 4.531,2.875 1.104,0.198 10 false Atmospheric Air 3.448,1.333 4.01,1.552 0.563,0.219 10 false Heater 3.448,1 4.01,1.219 0.563,0.219 10 false Alumina 3.375,1.615 4.646,2 1.271,0.385 10 false Solid Electrolyte (Zirconia Element) 5.625,2.792 6.552,3.01 0.927,0.219 10 false Air-Fuel Ratio 4.313,0.542 5.615,0.76 1.302,0.219 10 false A/F Sensor Voltage 4.313,0.198 5.396,0.417 1.083,0.219 10 false ECM Monitored 0.115,0.063 2.031,0.281 1.917,0.219 10 false for Automatic Transaxle Model

A173183E60
1.75,2.625 2.042,2.625 false 3.042,2.594 3.385,2.917 false 2.865,2.406 3.385,2.604 false 2.979,2 3.375,1.927 false 3.021,2.354 3.385,2.604 false 3.198,1.875 3.354,1.51 3.354,1.51 3.385,1.51 false 1.583,2.646 0.979,2.26 0.979,2.26 0.938,2.26 false 1.229,3.125 1.354,3.323 0.125,0.198 10 false A 1.896,3.125 2.021,3.323 0.125,0.198 10 false A 0.385,2.167 0.927,2.323 0.542,0.156 10 false Element 0.302,3.198 1.333,3.417 1.031,0.219 10 false Exhaust Gas 2.677,3.198 3.708,3.417 1.031,0.219 10 false A-A Section 3.396,2.521 4.604,2.74 1.208,0.219 10 false Platinum Electrode 2.073,2.521 2.635,2.74 0.563,0.219 10 false Cover 3.396,2.875 3.688,3.073 0.292,0.198 10 false Air 3.427,1.427 3.865,1.646 0.438,0.219 10 false Heater 3.396,1.823 4.583,2.208 1.188,0.385 10 false Solid Electrolyte (Zirconia Element) 5.385,3.021 7.094,3.24 1.708,0.219 10 false Rich - Air Fuel Ratio - Lean 5.635,0.615 6.99,0.833 1.354,0.219 10 false Ideal Air Fuel Mixture 4.573,0.833 5.563,1.146 0.99,0.313 10 false Output Voltage 0.177,0.167 2.885,0.406 2.708,0.24 10 false for Continuously Variable Transaxle Model

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.

·

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

·

When either of these DTCs is set, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.

A140671E01
0.099,0.064 2.848,0.252 2.749,0.188 10 Reference (System Diagram of Sensor 1) 1.316,0.858 1.549,1.039 0.233,0.181 10 EFI 2.121,0.62 2.763,0.801 0.642,0.181 10 EFI MAIN 3.747,0.402 4.461,0.584 0.714,0.181 10 A/F Sensor 3.466,1.005 3.657,1.186 0.191,0.181 10 +B 4.58,1.005 4.960,1.186 0.380,0.181 10 HA1A 3.361,1.576 3.687,1.757 0.326,0.181 10 A1A- 4.594,1.576 4.955,1.757 0.361,0.181 10 A1A+ 3.887,0.83 4.322,1.011 0.436,0.181 10 Heater 3.873,1.432 4.332,1.613 0.459,0.181 10 Sensor 5.876,0.353 6.202,0.535 0.326,0.181 10 ECM 5.204,0.998 5.584,1.179 0.380,0.181 10 HA1A 5.204,1.569 5.564,1.750 0.361,0.181 10 A1A+ 5.204,2.154 5.530,2.335 0.326,0.181 10 A1A- 5.204,2.721 5.606,2.902 0.403,0.181 10 MREL 0.48,1.031 0.971,1.391 0.492,0.360 10 From Battery



DTC No. DTC Detection Condition Trouble Area
P0031 Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A
(1 trip detection logic)
·

Open in A/F sensor heater circuit

·

A/F sensor (sensor 1)

·

ECM


P0032 Air-Fuel Ratio (A/F) sensor heater current reaches the high limit
(1 trip detection logic)
·

Short in A/F sensor heater circuit

·

A/F sensor (sensor 1)

·

ECM



MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
a.
U188227E02
2.229,0.99 1.823,1.219 false 0.073,0.063 1.385,0.24 1.313,0.177 10 false Wire Harness Side 0.885,0.438 2.313,0.635 1.427,0.198 10 false A/F Sensor Connector 0.552,1.146 0.823,1.344 0.271,0.198 10 false D56 0.396,1.438 1.094,1.635 0.698,0.198 10 false Sensor 1 2.26,0.865 2.531,1.063 0.271,0.198 10 false +B 1.292,1.844 2.01,2.042 0.719,0.198 10 false Front View

Disconnect the A/F sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D56-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (A/F SENSOR - EFI MAIN RELAY)

3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
a.

Disconnect the A/F sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
D56-1 (HA1A) - D2-109 (HA1A) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
D56-1 (HA1A) or D2-109 (HA1A) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester ON.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Allow the engine to idle for 1 minute or more.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.


i.

Read DTCs.


Result:
Display (DTC Output) Proceed to
No output A
P0031 or P0032 B



A

B