Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2111  Throttle Actuator Control System - Stuck Open  P2112  Throttle Actuator Control System - Stuck Closed  


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. DTC Detection Condition Trouble Area
P2111 The ECM signals the throttle actuator to close, but the actuator is stuck (1 trip detection logic).
·

Throttle actuator

·

Throttle body assembly

·

Throttle valve

·

Wire harness or connector

·

ECM


P2112 The ECM signals the throttle actuator to open, but the actuator is stuck (1 trip detection logic).
·

Throttle actuator

·

Throttle body assembly

·

Throttle valve

·

Wire harness or connector

·

ECM



FAIL-SAFE

When either of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Position No. 2, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2111 OR P2112)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P2111 or P2112 is output A
DTC P2111 or P2112 and other DTCs are output B

HINT:

If any DTCs other than P2111 or P2112 are output, troubleshoot those DTCs first.




A

2.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

B

2.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body assembly. Also check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.




OK

3.READ VALUE USING GTS (THROTTLE POSITION)

NG

5.REPLACE THROTTLE BODY ASSEMBLY
3.READ VALUE USING GTS (THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.


i.

Read the values displayed on the GTS while wiggling the ECM wire harness.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B



A

4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY ASSEMBLY)

B

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
4.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY ASSEMBLY)
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).



NEXT

END

5.REPLACE THROTTLE BODY ASSEMBLY
a.

Replace the throttle body assembly (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P2111 OR P2112)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Start the engine and fully depress and release the accelerator pedal quickly (to fully open and close the throttle valve).


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P2111 or P2112 is output B



A

END

B