Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM › 2013.04–2014.09
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM C

2AZ-FE ENGINE CONTROL  SFI SYSTEM  P2119  Throttle Actuator Control Throttle Body Range / Performance  


DESCRIPTION

The electronic throttle control system is composed of the throttle actuator, throttle position sensor, accelerator pedal position sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The throttle position sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No. DTC Detection Condition Trouble Area
P2119 The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic).
·

Electronic throttle control system

·

Wire harness or connector

·

ECM



FAIL-SAFE

When this DTC or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the engine switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Refer to "Data List / Active Test" [Throttle Position Commanded, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open) and Throttle Motor Duty (Close)] (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Result
Result Proceed to
DTC P2119 is output A
DTC P2119 and other DTCs are output B

HINT:

If any DTCs other than P2119 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

B

2.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position Command.


i.

Read the values displayed on the tester while fully depressing and releasing the accelerator pedal quickly.

Result
Result Proceed to
Throttle Position No. 1 does not change A
Throttle Position No. 1 changes even a little B

HINT:

When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.




A

3.INSPECT THROTTLE BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)

B

4.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
3.INSPECT THROTTLE BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body assembly (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>THROTTLE BODY>INSPECTION).



OK

4.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

7.REPLACE THROTTLE BODY ASSEMBLY
4.INSPECT THROTTLE BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body assembly. Also, check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.




OK

5.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)

NG

7.REPLACE THROTTLE BODY ASSEMBLY
5.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Turn the engine switch on (IG).


g.

Turn the tester on.


h.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.


i.

Read the values displayed on the tester while wiggling the ECM wire harness.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the DTCs.

Result
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B



A

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY ASSEMBLY)

B

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE BODY ASSEMBLY)
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).



NEXT

END

7.REPLACE THROTTLE BODY ASSEMBLY
a.

Replace the throttle body assembly (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the engine switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the tester on.


h.

Idle the engine for 20 seconds.


i.

Fully depress and release the accelerator pedal 3 times.


j.

Enter the following menus: Powertrain / Engine and ECT / DTC.


k.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P2119 is output B



A

END

B