Home › Engine / Hybrid System › 2AZ-FE ENGINE CONTROL › SFI SYSTEM
RM24M0E _51 Engine / Hybrid System _059541 2AZ-FE ENGINE CONTROL _0291789 SFI SYSTEM J

2AZ-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on signals from the ECM.

WIRING DIAGRAM

A218269E05
1.604,0.438 1.885,0.615 0.281,0.177 10 false G57 1.604,0.927 1.885,1.104 0.281,0.177 10 false G58 1.604,1.438 1.885,1.615 0.281,0.177 10 false G58 1.938,0.385 2.26,0.583 0.323,0.198 10 false AM1 1.938,0.885 2.281,1.042 0.344,0.156 10 false AM2 1.938,1.396 2.313,1.573 0.375,0.177 10 false IG2D 1.698,0.229 1.792,0.406 0.094,0.177 10 false 6 1.688,0.708 1.802,0.865 0.115,0.156 10 false 1 1.646,1.219 1.833,1.385 0.188,0.167 10 false 11 1.854,1.781 2.885,1.927 1.031,0.146 10 false Main Body ECU 0.521,3.323 1.25,3.469 0.729,0.146 10 false AM2 NO. 2 0.552,4.573 1.188,4.76 0.635,0.188 10 false F/B BATT 0.667,5.906 1.135,6.094 0.469,0.188 10 false Battery 2.073,4.594 2.333,4.781 0.26,0.188 10 false IG2 1.875,3.813 2.01,3.979 0.135,0.167 10 false 5 1.875,4.229 2,4.385 0.125,0.156 10 false 2 2.417,3.813 2.521,3.979 0.104,0.167 10 false 3 2.417,4.229 2.563,4.385 0.146,0.156 10 false 1 1.073,4.073 1.333,4.25 0.26,0.177 10 false IG2 6.063,6.344 6.344,6.521 0.281,0.177 10 false D2 5.99,1.375 6.26,1.552 0.271,0.177 10 false #10 5.99,2.198 6.26,2.375 0.271,0.177 10 false #20 5.99,3.052 6.26,3.229 0.271,0.177 10 false #30 5.99,3.885 6.26,4.063 0.271,0.177 10 false #40 5.99,5.01 6.26,5.188 0.271,0.177 10 false E01 5.99,5.729 6.26,5.906 0.271,0.177 10 false E02 5.625,1.281 5.896,1.469 0.271,0.188 10 false 108 5.635,2.104 5.906,2.292 0.271,0.188 10 false 107 5.635,2.948 5.906,3.135 0.271,0.188 10 false 106 5.646,3.802 5.917,3.99 0.271,0.188 10 false 105 5.708,4.885 5.906,5.073 0.198,0.188 10 false 45 5.708,5.625 5.906,5.813 0.198,0.188 10 false 44 4.073,1.656 5.323,1.844 1.25,0.188 10 false No. 1 Fuel Injector 4.073,2.458 5.333,2.813 1.26,0.354 10 false No. 2 Fuel Injector 4.073,3.313 5.333,3.667 1.26,0.354 10 false No. 3 Fuel Injector 4.073,4.146 5.333,4.5 1.26,0.354 10 false No. 4 Fuel Injector 6.344,6.344 6.677,6.542 0.333,0.198 10 false ECM 0.552,5.219 1.188,5.406 0.635,0.188 10 false FL MAIN 4.781,1.292 4.896,1.448 0.115,0.156 10 false 2 4.177,1.292 4.292,1.448 0.115,0.156 10 false 1 4.781,2.125 4.896,2.281 0.115,0.156 10 false 2 4.177,2.125 4.292,2.281 0.115,0.156 10 false 1 4.781,2.969 4.896,3.125 0.115,0.156 10 false 2 4.177,2.969 4.292,3.125 0.115,0.156 10 false 1 4.781,3.813 4.896,3.969 0.115,0.156 10 false 2 4.177,3.813 4.292,3.969 0.115,0.156 10 false 1 3.729,1.656 4.031,1.813 0.302,0.156 10 false D22 3.708,2.469 4.021,2.625 0.313,0.156 10 false D23 3.708,3.313 4.021,3.469 0.313,0.156 10 false D24 3.729,4.135 4.042,4.292 0.313,0.156 10 false D25

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FUEL INJECTOR (POWER SOURCE)
a.

Disconnect the fuel injector connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D22-1 - Body ground Engine switch on (IG) 11 to 14 V
D23-1 - Body ground Engine switch on (IG) 11 to 14 V
D24-1 - Body ground Engine switch on (IG) 11 to 14 V
D25-1 - Body ground Engine switch on (IG) 11 to 14 V




OK

2.INSPECT FUEL INJECTOR

NG

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - FUEL INJECTOR)
2.INSPECT FUEL INJECTOR
a.

Inspect the fuel injector (See page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)
a.

Disconnect the fuel injector connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D22-2 - D2-108 (#10) Always Below 1 Ω
D23-2 - D2-107 (#20) Always Below 1 Ω
D24-2 - D2-106 (#30) Always Below 1 Ω
D25-2 - D2-105 (#40) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D22-2 or D2-108 (#10) - Body ground Always 10 kΩ or higher
D23-2 or D2-107 (#20) - Body ground Always 10 kΩ or higher
D24-2 or D2-106 (#30) - Body ground Always 10 kΩ or higher
D25-2 or D2-105 (#40) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - FUEL INJECTOR)
a.

Disconnect the fuel injector connector.


b.

Remove the IG2 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D22-1 - 3 (IG2 relay terminal) Always Below 1 Ω
D23-1 - 3 (IG2 relay terminal) Always Below 1 Ω
D24-1 - 3 (IG2 relay terminal) Always Below 1 Ω
D25-1 - 3 (IG2 relay terminal) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D22-1 or 3 (IG2 relay terminal) - Body ground Always 10 kΩ or higher
D23-1 or 3 (IG2 relay terminal) - Body ground Always 10 kΩ or higher
D24-1 or 3 (IG2 relay terminal) - Body ground Always 10 kΩ or higher
D25-1 or 3 (IG2 relay terminal) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR