Refer to DTC P0031 (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P0031).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2237 | An open in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor while the engine is running (2 trip detection logic). | ·
Open in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
| P2238 | ·
Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a)
Voltage at terminal A1A+ is 0.5 V or less. (b)
Voltage difference between terminals A1A+ and A1A- is 0.1 V or less. ·
Case 2: Air fuel ratio sensor admittance is less than 0.015 1/Ω (2 trip detection logic). |
·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
| P2239 | The A1A+ voltage is higher than 4.5 V (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
| P2252 | The A1A- voltage is 0.5 V or less (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
| P2253 | The A1A- voltage is higher than 4.5 V (2 trip detection logic). | ·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
ECM |
These DTCs are output when there is an open or short in the air fuel ratio sensor circuit, or if the air fuel ratio sensor output drops. To detect these problems, the voltage of the air fuel ratio sensor is monitored when turning the engine switch on (IG), and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor is higher than 0.5 V, or 4.5 V or less, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM determines that there is a malfunction in the air fuel ratio sensor. If the same malfunction is detected in next driving cycle, the MIL is illuminated and a DTC is stored.
Refer to DTC P2195 (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>P2195).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Refer to "Data List / Active Test" [AFS Voltage B1S1] (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D56-1 (HA1A) - D2-109 (HA1A) | Always | Below 1 Ω |
| D56-3 (A1A+) - D2-112 (A1A+) | Below 1 Ω | |
| D56-4 (A1A-) - D2-113 (A1A-) | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D56-1 (HA1A) or D2-109 (HA1A) - Body ground | Always | 10 kΩ or higher |
| D56-3 (A1A+) or D2-112 (A1A+) - Body ground | 10 kΩ or higher | |
| D56-4 (A1A-) or D2-113 (A1A-) - Body ground | 10 kΩ or higher |
OK
NG
Replace the air fuel ratio sensor (See page Engine / Hybrid System>2AZ-FE EMISSION CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the tester on.
Start the engine and wait 5 minutes or more.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2237, P2238, P2239, P2252 or P2253.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2237, P2238, P2239, P2252 or P2253 is output) | B |
A
B