Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL INJECTOR
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291796 FUEL INJECTOR A

2AZ-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

a.
A097400E11
3.083,1.542 2.802,1.781 false 1.979,1.74 2.833,1.938 0.854,0.198 10 false New O-Ring

Apply a light coat of gasoline or spindle oil to new O-rings, then install one onto each fuel injector.


b.
A131629E01
1.169,0.151 1.937,0.351 0.768,0.200 10 CORRECT 1.076,1.418 1.955,1.608 0.879,0.190 10 INCORRECT 0.272,2.691 0.746,2.881 0.474,0.190 10 O-Ring 1.052,2.794 1.931,2.984 0.879,0.190 10 Delivery Pipe 0.753,2.319 0.548,2.662 false 1.314,2.4 1.498,2.794 false

Apply a light coat of gasoline or spindle oil to the part of the fuel delivery pipe which comes into contact with the O-ring of the fuel injector.


c.

Apply a light coat of gasoline or spindle oil to the O-ring again, then install the right and left fuel injectors onto the fuel delivery pipe.

NOTICE:

Make sure that the O-ring is not cracked or jammed when installing it.



d.

Check that the fuel injector rotates smoothly.

If the fuel injector does not rotate smoothly, replace the O-ring.


Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A125335

Install 4 new insulators into the cylinder head.


b.

Install the 2 delivery pipe spacers onto the cylinder head.


c.
A097444E15
2.594,0.521 2.594,1.313 false 1.698,0.219 2.094,0.531 false 1,0.875 1.74,0.875 false 1.052,1.667 0.802,1.302 false 0.198,1.167 0.813,1.333 0.615,0.167 10 false Insulator 1.969,1.302 3.146,1.469 1.177,0.167 10 false Fuel Delivery Pipe 1.104,0.052 1.583,0.219 0.479,0.167 10 false O-Ring 0.156,0.76 0.958,0.938 0.802,0.177 10 false Fuel Injector

Install the fuel delivery pipe together with the 4 fuel injectors, then temporarily tighten the 2 bolts.

NOTICE:

Be careful not to drop the fuel injectors when installing the fuel delivery pipe.



d.

Check that the fuel injector rotates smoothly.

If the fuel injector does not rotate smoothly, replace the O-ring.


e.
A125334

Tighten the 2 bolts to the specified torque.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


f.
A125333

Connect the 4 fuel injector connectors.


g.

Install the 2 wire harness clamps.


Hide 12262 3.CONNECT NO. 2 VENTILATION HOSE

a.
A095428E07
2.635,0.396 2.25,0.156 2.25,0.156 1.427,0.156 false 0.219,0.063 1.375,0.229 1.156,0.167 10 false White Paint Mark 1.573,0.323 1.854,0.49 0.281,0.167 10 false "A" 2.698,0.094 2.979,0.26 0.281,0.167 10 false UP 3.135,0.521 3.375,0.688 0.24,0.167 10 false LH 2.406,1.042 3.094,1.208 0.688,0.167 10 false View: "A"

Connect the ventilation hose to the ventilation valve.

NOTICE:

Make sure that the paint mark and hose clamp are at the correct angle when installing the hose.



Hide 77251B 4.CONNECT FUEL MAIN TUBE

a.

Connect the fuel main tube.


b.

Push the fuel tube connector until it makes a "click" sound.


c.

Install the fuel pipe clamp.


d.

Install the fuel tube into the fuel hose clamp.


Hide 6.INSTALL COWL TOP OUTER PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

a.

Install the cowl top outer panel with windshield wiper motor and link (see page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 28800 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 8.PERFORM INITIALIZATION

a.

Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



Hide 9.CHECK FOR FUEL LEAKAGE

a.
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the engine switch on (IG), and push the intelligent tester main switch ON.

NOTICE:

Do not start the engine.



iii.

Select the Active Test mode on the intelligent tester.

HINT:

Refer to the intelligent tester operator's manual for further details.



iv.

Check that there are no leaks from the fuel system.


v.

Turn the engine switch off.


vi.

Disconnect the intelligent tester from the DLC3.