Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL TANK
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291800 FUEL TANK A

2AZ-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77100 1.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank on a mission jack.


b.

Lift up the mission jack.


c.
A131614

Install the fuel tank bracket and 2 fuel tank bands with the 6 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:

First temporarily install the bolts of the tank bracket. Then temporarily install the bolts of the tank bands. Finally, tighten all of the bolts.



Hide 77707 2.CONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A134871

Install the outlet tube to the fuel tank.


Hide 77213B 3.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A135882E01
0.606,2.524 0.977,2.689 0.371,0.165 10 Front 2.231,2.3 2.559,2.465 0.327,0.165 10 180° 0.747,2.783 1.268,2.973 0.521,0.190 10 Marking 1.712,2.673 1.476,2.893 false 1.48,2.894 1.4,2.894 false

Connect the filler pipe hose to the fuel tank.


Hide 77221 4.CONNECT NO. 1 FUEL TANK BREATHER TUBE

a.
A131611

Connect the fuel tank breather tube to the fuel tank.

NOTICE:
·

Before installing the pipe, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.


·

After connecting, check if the pipe and the connector are securely connected by pulling on them.




Hide 77209D 5.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

NOTICE:

Before installing the tube connector to the pipe, check the connector for damage and foreign matter.


a.
A131609E01
1.856,2.815 2.432,2.996 0.575,0.180 10 Retainer 2.482,2.579 2.185,2.704 false 2.185,2.704 2.185,2.815 false

Connect the main tube connector to the pipe and install the retainer. Push the 2 parts together firmly until a "click" sound is heard.

NOTICE:

Check that the connector and pipe are securely connected by trying to pull them apart.



Hide 77026A 6.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the purge line hose to the pipe.


Hide 58166A 7.INSTALL FRONT FLOOR COVER LH

a.
A131607

Install the floor cover with the 4 bolts.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 77020A 8.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77209D 9.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77707 10.CONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A139346

Connect the outlet tube to the fuel suction with pump and gauge.


Hide 58325E 11.INSTALL REAR FLOOR SERVICE HOLE COVER

a.
A126805

Connect the fuel pump connector.


b.

Install the service hole cover with new butyl tape.


Hide 12.ADD FUEL

Hide 77310A 13.INSTALL FUEL TANK CAP

Hide 28800 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 15.PERFORM INITIALIZATION

a.

Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.