Home › Engine / Hybrid System › 2AZ-FE FUEL › FUEL SYSTEM
RM24M0E _51 Engine / Hybrid System _059542 2AZ-FE FUEL _0291801 FUEL SYSTEM G

2AZ-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION

a.
B135940E01
0.425,2.845 1.557,3.021 1.132,0.177 10 Intelligent Tester 0.6,2.589 0.6,2.832 false 1.48,2.058 1.864,2.214 0.385,0.156 10 DLC3 1.717,2.051 1.841,1.732 false

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG). Do not start the engine.


c.

Select the following tester menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


d.

Touch the fuel hose in the engine compartment to check the fuel flow, and you will also be able to hear the sound of the fuel pump.


e.

Stop the fuel pump.

If there is no fuel flow, the fuel pump may not operate. Check the fuel pump circuit (see page Engine / Hybrid System>2AZ-FE FUEL>FUEL PUMP>INSPECTION).


Hide 2.CHECK FUEL PRESSURE

a.

Check that the battery positive voltage is above 12 V.


b.

Discharge the fuel system pressure (see page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>REMOVAL).


c.

Disconnect the cable from the negative (-) battery terminal.


d.

Disconnect the fuel main tube (see page Engine / Hybrid System>2AZ-FE FUEL>FUEL INJECTOR>REMOVAL).


e.
A255967E12
0.844,0.49 0.604,0.49 false 1.51,0.781 1.51,1.073 false 1.104,0.99 1.104,1.177 false 2.844,0.417 2.573,0.177 2.573,0.177 2.448,0.177 false 1.615,3.344 1.875,3.083 1.875,3.083 1.958,3.083 false 1.302,3.979 1.438,4.115 1.438,4.115 1.531,4.115 false 2.75,3.302 2.75,3.604 false 2.365,3.563 2.365,3.792 false 0.594,1.146 0.438,0.969 0.438,0.969 0.354,0.969 false 1.177,0.323 1.375,0.323 false 0.396,0.396 0.552,0.552 0.156,0.156 10 false *a 1.438,1.104 1.646,1.292 0.208,0.188 10 false *a 1.031,1.198 1.24,1.406 0.208,0.208 10 false *b 2.25,0.104 2.406,0.26 0.156,0.156 10 false *c 1.406,0.24 1.563,0.396 0.156,0.156 10 false *d 0.135,0.885 0.292,1.042 0.156,0.156 10 false *1 2.292,3.813 2.5,4.01 0.208,0.198 10 false *f 1.969,2.99 2.125,3.146 0.156,0.156 10 false *a 1.552,4.021 1.854,4.229 0.302,0.208 10 false *e 2.688,3.635 2.906,3.854 0.219,0.219 10 false *g

Install SST (EFI fuel pressure gauge) as shown in the illustration.

Text in Illustration
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)
09268-45014  (09268-41200, 09268-41220, 09268-41250)


f.

Wipe off any gasoline.


g.

Reconnect the cable to the negative (-) battery terminal.


h.

Start the engine.


i.

Measure the fuel pressure at idle.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


If the pressure is not as specified, check the fuel pump and injectors.


j.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST and the fuel tube connector to prevent fuel from spilling.


k.

Reconnect the fuel main tube (see page Engine / Hybrid System>2AZ-FE FUEL>FUEL SYSTEM>PRECAUTION).


l.