Home › Engine / Hybrid System › 2GR-FE FUEL › FUEL PUMP
RM24M0E _51 Engine / Hybrid System _059543 2GR-FE FUEL _0291805 FUEL PUMP A

2GR-FE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A191110E08
2.104,0.438 2.24,0.583 false 2.24,0.583 2.344,0.583 false 2.375,0.5 3.219,0.854 0.844,0.354 10 false New Gasket

Install a new gasket onto the fuel pump.


b.
U188467E02
1.104,0.938 1.26,0.792 false 0.635,0.281 1.406,0.615 0.771,0.333 10 false Upper Side 0.271,1.396 1.052,1.719 0.781,0.323 10 false Front Side 1.323,0.677 1.74,0.917 0.417,0.24 10 false Mark

Connect the fuel hose and install the fuel pump into the fuel tank.

NOTICE:
·

When connecting the fuel hose, make sure the fuel hose marking faces upward and that the grip part of the clamp faces the front of the vehicle.


·

Be careful not to bend the arm of the fuel sender gauge.


·

When connecting the fuel hose, do not forcibly pull the hose.




Hide 77168A 2.INSTALL FUEL TANK VENT TUBE SET PLATE

a.
A126809E05
1.354,1.344 1.438,1.177 false 1.427,1.177 1.594,1.177 false 1.323,1.406 1.063,1.854 false 1.063,1.854 0.938,1.854 false 0.208,1.76 0.896,2.052 0.688,0.292 10 true Protrusion 1.615,1.094 2.135,1.396 0.521,0.302 10 true Groove

Install the set plate with the 8 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:

Align the protrusion of the set plate with the groove of the fuel pump.



Hide 77209D 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A126808

a.
A124131E10
0.313,0.146 0.125,0.146 0.125,0.146 0.969,0.885 false 0.99,1.219 0.698,1.51 0.698,1.51 1,1.396 false 1.615,1.052 2.146,1.438 false 1.271,2.51 1.427,2.51 1.427,2.51 1.104,3.188 false 0.771,3.365 1,3.708 1,3.708 1.135,3.708 false 2.448,3.302 2.563,2.823 2.563,2.823 2.667,2.823 false 2.375,0.167 2.073,0.167 2.073,0.167 1.885,0.563 false 0.375,0.063 1.438,0.26 1.063,0.198 10 false Fuel Tube Joint 2.427,0.083 3.125,0.292 0.698,0.208 10 false Fuel Tube 0.229,1.438 0.75,1.667 0.521,0.229 10 false O-Ring 0.344,2.427 1.313,2.656 0.969,0.229 10 false Tube Joint Clip 2.229,1.365 3.219,1.594 0.99,0.229 10 false Tube Joint Clip 1.177,3.625 1.688,3.792 0.51,0.167 10 false Collars 0.417,4.302 1.177,4.5 0.76,0.198 10 false CORRECT 2.063,4.302 2.958,4.479 0.896,0.177 10 false INCORRECT 2.708,2.74 3.219,2.906 0.51,0.167 10 false Collars

Install the fuel tube with the joint clip.

CAUTION:
·

Check that there are no scratches or foreign objects on the connecting parts.


·

Check that the fuel tube joint is inserted securely.


·

Check that the fuel tube joint clip is on the collars of the fuel tube joint.


·

After installing the tube joint clip, check that the fuel tube joint has not been pulled off.


·

Be careful not to damage the clip. If the clip is damaged, replace it.




Hide 77027 4.CONNECT NO. 2 FUEL EVAPORATION TUBE SUB-ASSEMBLY

A139141

a.

Connect the tube to the fuel tube assembly.

NOTICE:
·

Before installing the pipe, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.


·

After connecting, check if the pipe and the connector are securely connected by pulling on them.




Hide 77026A 5.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the tube to the fuel tube assembly.


Hide 77707 6.CONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.

Connect the outlet tube to the fuel tube assembly.


Hide 58325E 7.INSTALL REAR FLOOR SERVICE HOLE COVER

a.
A126805

Connect the fuel pump connector.


b.

Install the service hole cover with new butyl tape and return the floor carpet to its original position.


Hide 77310A 8.INSTALL FUEL TANK CAP

Hide 72129 9.INSTALL NO. 1 SEAT TRACK LOWER RAIL PROTECTOR

B144647

a.

Align the seat track lower rail protector with the edge of the rear seat track bracket at the front end of the rail, engage the claw, and install the protector.

HINT:

Use the same procedure for the other seat track lower rail protector.



Hide 58595 10.INSTALL NO. 3 FLOOR CARPET MOULDING

a.

Engage the clip to install the No. 3 floor carpet moulding.

HINT:

Use the same procedure for the other No. 3 floor carpet mouldings.



Hide 11.INSTALL REAR NO. 1 SEAT ASSEMBLY (for Captain Seat Type)

Hide 71940A 12.INSTALL REAR SEAT HEADREST ASSEMBLY (for Captain Seat Type)

Hide 13.INSTALL REAR SEAT ASSEMBLY (for Tumble Seat Type LH Side)

Hide 71940A 14.INSTALL REAR SEAT HEADREST ASSEMBLY (for Tumble Seat Type LH Side)

Hide 28800 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL