51441
1.REMOVE NO. 1 ENGINE UNDER COVER
11209
2.REMOVE V-BANK COVER ASSEMBLY
3.DRAIN ENGINE COOLANT
Remove the hood to cowl top seal.
Remove the cowl top ventilator louver cover.
Loosen the radiator drain cock plug, then drain the engine coolant.
| *1 | Radiator Reservoir | *2 | Radiator Reservoir Cap |
| *3 | Radiator Drain Cock Plug | *4 | Air Drain Cock Plug |
| *5 | Cylinder Block Drain Cock Plug (for Bank 1) | *6 | Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug) |
Collect the engine coolant in a container and dispose of it according to the regulations in your area.
Loosen the cylinder block drain cock plug (for Bank 1).
Loosen the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).
Remove the radiator reservoir cap.
Do not remove the radiator reservoir cap while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
4.ADD ENGINE COOLANT
Tighten the radiator drain cock plug by hand.
Tighten the cylinder block drain cock plug (for Bank 1).
Tighten the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).
Remove the air drain cock plug from the water inlet housing.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator reservoir until engine coolant overflows from the air drain cock hole. Then install the air drain cock plug to the water inlet housing.
Check the identification mark on the fan shroud.
| *a | Identification Mark |
Continue adding TOYOTA SLLC until it is filled to the B line at the base of the reservoir filler neck.
| *a | B Line |
| Item | Identification Mark | Condition | Specified Condition |
|---|---|---|---|
| Engine Coolant | 1, 3 | w/ Rear Heater | 10.9 liters (11.5 US qts, 9.6 Imp. qts) |
| w/o Rear Heater | 9.1 liters (9.6 US qts, 8.0 Imp. qts) | ||
| 8 | w/ Rear Heater | 10.6 liters (11.2 US qts, 9.3 Imp. qts) | |
| w/o Rear Heater | 8.7 liters (9.2 US qts, 7.7 Imp. qts) |
Never use water as a substitute for engine coolant.
TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant. If the engine coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
The thermostat open timing can be confirmed by squeezing the No. 1 radiator hose and No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the No. 2 radiator hose.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air.
When squeezing the No. 1 radiator hose and No. 2 radiator hose:
Wear protective gloves.
Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.
Keep your hands away from the fan.
Make sure that the radiator reservoir still has some engine coolant in it.
If the engine coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
If there is not enough engine coolant, the engine may overheat or be seriously damaged.
If the radiator reservoir does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the engine coolant is filled to the B line.
Stop the engine and wait until the engine coolant cools down to ambient temperature.
Check that the engine coolant level is between the FULL and LOW line.
If the engine coolant level is below the LOW line, repeat all of the procedures above.
If the engine coolant level is above the FULL line, drain engine coolant so that the engine coolant level is between the FULL and LOW line.
Install the cowl top ventilator louver cover.
Install the hood to cowl top seal.
5.INSPECT FOR COOLANT LEAK
11209
6.INSTALL V-BANK COVER ASSEMBLY
51441
7.INSTALL NO. 1 ENGINE UNDER COVER