11301C
1.INSTALL TIMING CHAIN CASE OIL SEAL
Using SST, tap in a new oil seal until its surface is flush with the timing chain case edge.
Keep the lip free from foreign matter.
Do not tap on the oil seal at an angle.
Make sure that the oil seal edge does not stick out of the timing chain case.
11302
2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Apply seal packing in a continuous line to the engine unit as shown in the following illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 mm (0.118 in.)
Be sure to clean and degrease the contact surfaces, especially the surfaces indicated by C in the illustration.
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the chain cover within 3 minutes.
Do not start the engine for at least 2 hours after installing.
Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Do not start the engine for at least 2 hours after installing it.
| Area | Seal Packing Diameter | Application Position from Inside Seal Line |
|---|---|---|
| Continuous Line Area | 4.5 mm (0.177 in.) or more | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Alternate Long and Short Dashed Line Area | 3.5 mm (0.138 in.) or more | 2.0 to 3.0 mm (0.079 to 0.118 in.) |
| Dashed Line Area | 3.5 mm (0.138 in.) or more | 3.0 to 4.0 mm (0.118 to 0.158 in.) |
| Diagonal Line Area | 6.0 mm (0.236 in.) or more | 5.0 mm (0.197 in.) |
Install a new gasket.
Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.
Type X:
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
| Item | Length |
|---|---|
| Bolt A | 40 mm (1.57 in.) |
| Bolt B | 55 mm (2.17 in.) |
| Bolt C | 25 mm (0.98 in.) |
Make sure that there is no oil on the bolt threads.
Type Y:
Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.
| Item | Length |
|---|---|
| Bolt A | 40 mm (1.57 in.) |
| Bolt B | 55 mm (2.17 in.) |
| Bolt C | 28 mm (1.102 in.) |
Make sure that there is no oil on the bolt threads.
Fully tighten the bolts in: Area 1 and Area 2.
Fully tighten the bolts and nuts in: Area 3.
Tighten the bolts and nuts from top to bottom as shown in the illustration.
Fully tighten the bolts in: Area 4.
Tighten the bolts from bottom to top as shown in the illustration.
16323
3.INSTALL WATER INLET HOUSING
12101
4.INSTALL OIL PAN SUB-ASSEMBLY
15104
5.INSTALL OIL STRAINER SUB-ASSEMBLY
12102A
6.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
11201
7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)
11201
8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)
13471
9.INSTALL CRANKSHAFT PULLEY
15771
10.INSTALL NO. 1 OIL PIPE
15771M
11.INSTALL OIL PIPE
12.INSTALL ENGINE OIL LEVEL DIPSTICK
13.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE