Home › Engine / Hybrid System › 2GR-FE COOLING › WATER PUMP › 2013.04–2016.05
RM24M0E _51 Engine / Hybrid System _059551 2GR-FE COOLING _0291842 WATER PUMP A

2GR-FE COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 1.INSTALL WATER PUMP ASSEMBLY

a.
A128115E14
0.542,0.438 0.698,0.604 0.156,0.167 10 true B 2.365,1.573 2.49,1.75 0.125,0.177 10 true B 2.469,0.396 2.594,0.563 0.125,0.167 10 true B 2.688,0.448 2.823,0.604 0.135,0.156 10 true B 2.76,0.031 2.906,0.219 0.146,0.188 10 true B 0.094,0.563 0.219,0.729 0.125,0.167 10 true A 1.323,0.51 1.448,0.688 0.125,0.177 10 true A 3.208,0.563 3.365,0.74 0.156,0.177 10 true A 0.531,1.813 0.677,2 0.146,0.188 10 true A 1.479,1.958 1.625,2.125 0.146,0.167 10 true A 2.688,1.771 2.813,1.979 0.125,0.208 10 true A 3.271,1.635 3.385,1.823 0.115,0.188 10 true A 0.948,0.417 1.073,0.594 0.125,0.177 10 true C 1.083,1.74 1.219,1.917 0.135,0.177 10 true C 2.094,1.938 2.208,2.115 0.115,0.177 10 true B 0.115,1.781 0.271,1.979 0.156,0.198 10 true A

Install a new water pump gasket and the water pump assembly with the 16 bolts.

Torque:
Bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolts B and C : 9.1 N*m (93 kgf*cm, 81 in.*lbf)

NOTICE:
·

Make sure that there is no oil on the threads of bolts A.

·

Be sure to replace 2 bolts C with new ones or reuse them after applying adhesive 1344.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent





Hide 16323 2.INSTALL WATER INLET HOUSING

a.
A128122

Install a new water inlet housing No. 1 gasket and water outlet pipe O-ring.


b.
A133375E07
1.302,1.219 1.594,0.927 false 1.396,0.438 1.792,0.573 false 1.802,0.458 2.594,0.854 0.792,0.396 10 true Water Hose 1.615,0.833 2.875,1.177 1.26,0.344 10 true Water Inlet Housing

Install the water inlet housing with the 2 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Be careful not to allow the O-ring to get caught between the parts.



c.

Connect the water hose.


Hide 16173 3.INSTALL WATER PUMP PULLEY

a.
A128112E05
2.594,0.573 2,0.167 false 1.656,0.042 1.99,0.323 0.333,0.281 10 true SST

Temporarily install the water pump pulley with the 4 bolts.


b.

Using SST, hold the water pump pulley.

SST
09960-10010  (09962-01000, 09963-00700)


c.

Tighten the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 16620 4.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A161449

Install the V-ribbed belt tensioner assembly with the 5 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16604 5.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.
A162789

Install the idler pulley cover plate and idler pulley sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12315 6.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

Hide 88310D 7.INSTALL COMPRESSOR AND MAGNETIC CLUTCH

Hide 10.REMOVE ENGINE STAND

Hide 11.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE