Home › Engine / Hybrid System › 2AZ-FE IGNITION › IGNITION SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059556 2AZ-FE IGNITION _0291865 IGNITION SYSTEM G

2AZ-FE IGNITION  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

The type of ignition switch on this model differs according to the specifications of the vehicle. For the expressions used in this section, refer to the "EXPRESSIONS OF IGNITION SWITCH" precaution (see page Engine / Hybrid System>2AZ-FE STARTING>STARTING SYSTEM>PRECAUTION).


PROCEDURE

Hide 19100P 1.PERFORM SPARK TEST

NOTICE:

In this section, the terms "Cold" and "Hot" refer to the temperature of the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).


a.

Check for DTCs.

NOTICE:

If a DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Check that sparks occur.

i.

Remove the cowl top outer panel with windshield wiper motor and link (see page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


ii.

Remove the bolt and ignition coil assembly.


iii.
A124849E02
0.833,1.396 0.885,1.438 0.052,0.042 0.865,1.427 0.885,1.438 0.021,0.01 1.115,1.25 1.844,0.115 1.844,0.115 2.052,0.115 false 2.104,0.021 2.99,0.75 0.885,0.729 10 true 16 mm Spark Plug Wrench

Using a 16 mm spark plug wrench, remove the spark plugs.


iv.
A097448

Disconnect the 4 fuel injector connectors.


v.
A124396

Install the spark plug into the ignition coil assembly, and then connect the ignition coil connectors.


vi.

Ground the spark plug.


vii.

Check that sparks occur at the spark plug while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

·

If a spark plug has been struck or dropped, replace it.

·

If an ignition coil assembly has been struck or dropped, replace it.



If sparks do not occur, perform troubleshooting using the spark test flowchart.


viii.

Using a 16 mm plug wrench, install the spark plug.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


ix.

Install the ignition coil assembly with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


x.

Connect the 4 fuel injector connectors.


xi.

Install the cowl top outer panel with windshield wiper motor and link (see page Vehicle Interior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).





Hide 19500 2.INSPECT IGNITION COIL AND SPARK TEST

a.

Check that the wire harness side connector of the ignition coil assembly is securely connected.

Result
Result Action
NG Connect securely
OK Go to next step


b.

Perform a spark test on each ignition coil assembly.

i.

Replace the ignition coil assembly with a known good one.


ii.

Perform the spark test again.

Result
Result Action
NG Go to next step
OK Replace ignition coil assembly



c.

Perform a spark test on each spark plug.

i.

Replace the spark plug with a known good one.


ii.

Perform the spark test again.

Result
Result Proceed to
NG Inspect the ignition system (See page (Click here))
OK Replace spark plug



Hide 19100P 3.CHECK SPARK PLUG

a.
I039522E98
0.823,1.948 1.094,1.979 false 0.333,1.844 0.938,2.042 0.604,0.198 10 false Ground

Check the electrode with a megohmmeter:

i.

Using a megohmmeter, measure the insulation resistance.

Standard insulation resistance:

10 MΩ or more


If the result is 10 MΩ or less, clean the plug and measure the resistance again.



b.
A126881

Check the electrode without a megohmmeter:

i.

Quickly accelerate the engine to 4,000 rpm 5 times.


ii.

Remove the spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage on its threads and insulator.

If there is damage, replace the spark plug.

Recommended spark plug:
Manufacturer Spark plug type
DENSO SK16R11
NGK IFR5A11



d.
A126880E01
0.66,1.582 1.587,1.769 0.927,0.187 10 1.0 to 1.1 mm

U110721

Check the spark plug electrode gap.

Maximum electrode gap for used spark plug:

1.3 mm (0.051 in.)


If the gap is greater than the maximum, replace the spark plug.

Electrode gap for new spark plug:

1.0 to 1.1 mm (0.039 to 0.043 in.)


If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard air pressure:

588 kPa (6 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.