Home › Brake › BRAKE › REAR BRAKE FLEXIBLE HOSE
RM24M0E _54 Brake _059558 BRAKE _0291880 REAR BRAKE FLEXIBLE HOSE A

BRAKE  REAR BRAKE FLEXIBLE HOSE  INSTALLATION  


PROCEDURE

Hide 47321B 1.INSTALL REAR BRAKE TUBE FLEXIBLE HOSE

NOTICE:

Because the left and right hoses are not interchangeable, verify the part number when installing the flexible hose.


a.

Set the flexible hose to the connecting point with the brake tubes (labeled A, B), and then attach 2 new clips (labeled C, D).

C364206E02
2.26,0.865 2.479,1.042 0.219,0.177 10 false A 0.208,0.146 0.865,0.396 0.656,0.25 10 false for LH: 3.677,0.115 4.177,0.344 0.5,0.229 10 false for RH: 2.51,1.198 2.729,1.375 0.219,0.177 10 true C 1.271,2.042 1.458,2.219 0.188,0.177 10 true B 1.469,1.885 1.625,2.042 0.156,0.156 10 true D 4.729,1.281 4.948,1.458 0.219,0.177 10 false A 4.979,1.271 5.198,1.448 0.219,0.177 10 false C 4.521,2.427 4.74,2.604 0.219,0.177 10 false B 4.792,2.365 5.01,2.542 0.219,0.177 10 false D


b.

Using SST, connect the flexible hose to the brake tubes (labeled A, B) while holding the flexible hose with a wrench.

SST
09023-00101  

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

without SST

14 N*m (144 kgf*cm, 10 ft.*lbf)

with SST


HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

·

This torque value is effective when SST is parallel to a torque wrench.



NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.




c.

for RH:

Install the front floor No. 2 heat insulator and tailpipe (for 2AZ-FE: see page Engine / Hybrid System>2AZ-FE EXHAUST>EXHAUST PIPE>INSTALLATION, for 2GR-FE: Engine / Hybrid System>2GR-FE EXHAUST>EXHAUST PIPE>INSTALLATION).


Hide 47319F 2.INSTALL REAR FLEXIBLE HOSE LH

NOTICE:

Because the left and right hoses are not interchangeable, verify the part number when installing the flexible hose.


HINT:
·

Use the same procedures for the LH side and RH side.

·

The procedures listed below are for the LH side.



a.
C133742E06
1.885,0 2.052,0.188 0.167,0.188 10 false C 0.406,1.781 0.573,1.969 0.167,0.188 10 false A 2.542,0.698 2.708,0.885 0.167,0.188 10 true B

Connect the flexible hose with a new gasket and a new union bolt (labeled A) to the disc brake cylinder.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

HINT:

Install the flexible hose lock securely in the lock hole in the cylinder.



b.

Set the flexible hose to the connecting point with the brake tube (labeled B), and then attach a new clip (labeled C).


c.

Using SST, connect the flexible hose to the brake tube (labeled B) while holding the flexible hose with a wrench.

SST
09023-00101  

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

without SST

14 N*m (144 kgf*cm, 10 ft.*lbf)

with SST


HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

·

This torque value is effective when SST is parallel to a torque wrench.



NOTICE:
·

Do not bend or damage the brake tube.

·

Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting point.




Hide 3.FILL RESERVOIR WITH BRAKE FLUID

Hide 4.BLEED AIR FROM BRAKE MASTER CYLINDER

Hide 5.BLEED AIR FROM BRAKE LINE

Hide 6.CHECK BRAKE FLUID LEVEL IN RESERVOIR

Hide 7.INSPECT FOR BRAKE FLUID LEAK

Hide 8.INSTALL REAR WHEEL

T = 103 N*m{ 1,050 kgf*cm 76 ft.*lbf }