Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor assembly, spiral cable sub-assembly and steering pad assembly.

The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1800/51
·

The center airbag sensor assembly detects a line short in the driver side squib circuit during the primary check.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Center airbag sensor assembly malfunction


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad assembly (Driver side squib)

·

Center airbag sensor assembly


B1801/51
·

The center airbag sensor assembly detects an open in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Center airbag sensor assembly malfunction


B1802/51
·

The center airbag sensor assembly detects a short to ground in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Center airbag sensor assembly malfunction


B1803/51
·

The center airbag sensor assembly detects a short to B+ in the driver side squib circuit.

·

Spiral cable sub-assembly malfunction

·

Driver side squib malfunction

·

Center airbag sensor assembly malfunction



WIRING DIAGRAM

C348666E13
2.115,1.052 2.688,1.479 0.573,0.427 10 false D+ 2.417,1.021 2.99,1.448 0.573,0.427 10 false 2 2.396,1.885 2.969,2.313 0.573,0.427 10 false 1 2.146,1.885 2.719,2.313 0.573,0.427 10 false D- 4.51,1.052 5.083,1.479 0.573,0.427 10 false 5 4.49,1.885 5.063,2.313 0.573,0.427 10 false 6 4.75,3.031 5.323,3.458 0.573,0.427 10 false G19 2.708,2.552 3.281,2.979 0.573,0.427 10 false G11 0.708,2.521 1.281,2.948 0.573,0.427 10 false i1 0.708,2.688 2.208,3.198 1.5,0.51 10 false Steering Pad Assembly (Driver Side Squib) 2.698,2.729 3.677,3.219 0.979,0.49 10 false Spiral Cable Sub-assembly 4.74,3.198 6.729,3.604 1.99,0.406 10 false Center Airbag Sensor Assembly 3.25,1.052 3.823,1.479 0.573,0.427 10 false D+ 4.719,1.177 5.292,1.604 0.573,0.427 10 false D+ 3.271,1.906 3.844,2.333 0.573,0.427 10 false D- 4.74,2.01 5.313,2.438 0.573,0.427 10 false D- 3.51,1.896 4.083,2.323 0.573,0.427 10 false 2 3.521,1.052 4.094,1.479 0.573,0.427 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241740E06
0.205,1.342 0.361,1.494 0.156,0.152 10 *1 1.03,0.798 1.197,0.963 0.167,0.165 10 *2 2.698,1.106 2.873,1.262 0.174,0.156 10 *3 1.902,1.342 2.055,1.494 0.153,0.151 10 *4 2.368,0.798 2.484,0.951 0.117,0.153 10 A 2.102,0.798 2.219,0.951 0.117,0.153 10 B 1.754,0.798 1.881,0.951 0.127,0.153 10 C 1.492,0.798 1.619,0.951 0.127,0.153 10 D 0.641,0.798 0.768,0.951 0.127,0.153 10 E 0.389,0.798 0.516,0.951 0.127,0.153 10 F 1.988,0.947 1.988,1.336 false 0.287,0.947 0.287,1.336 false

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the steering pad assembly, spiral cable sub-assembly and center airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the steering pad assembly, spiral cable sub-assembly and center airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable sub-assembly connector (on the steering pad assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and spiral cable sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Steering Pad Assembly
*2 Spiral Cable Sub-assembly
*3 Center Airbag Sensor Assembly
*4 Instrument Panel Wire



OK

2.CHECK STEERING PAD ASSEMBLY

NG

REPLACE WIRE HARNESS

2.CHECK STEERING PAD ASSEMBLY
a.
U189579E02
1.76,2.292 1.948,2.292 false 0.323,0.667 0.323,0.958 false 0.427,0.521 0.531,0.677 0.104,0.156 10 false F 0.75,0.521 0.875,0.677 0.125,0.156 10 false E 1.594,0.521 1.719,0.677 0.125,0.156 10 false D 1.75,0.521 1.875,0.677 0.125,0.156 10 false C 2.177,0.521 2.302,0.677 0.125,0.156 10 false B 2.333,0.521 2.458,0.677 0.125,0.156 10 false A 1.125,0.521 1.302,0.698 0.177,0.177 10 false *2 0.24,0.958 0.396,1.135 0.156,0.177 10 false *1 2.698,0.76 2.875,0.906 0.177,0.146 10 false *3 0.302,1.698 0.479,1.865 0.177,0.167 10 false *a 1.99,2.24 2.281,2.396 0.292,0.156 10 false SST 0.49,2.292 0.656,2.448 0.167,0.156 10 false i1

Connect the instrument panel wire to the center airbag sensor assembly and spiral cable sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the steering pad assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Steering Pad Assembly
*2 Spiral Cable Sub-assembly
*3 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Steering Pad Assembly)



A

B

C

3.CHECK DRIVER SIDE SQUIB CIRCUIT
3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
U189556E02
0.323,0.677 0.323,0.958 false 1.281,2.052 0.99,2.052 true 1.781,2.052 1.49,2.052 true 0.438,0.531 0.542,0.688 0.104,0.156 10 false F 0.75,0.531 0.875,0.688 0.125,0.156 10 false E 1.594,0.531 1.719,0.688 0.125,0.156 10 false D 1.76,0.531 1.885,0.688 0.125,0.156 10 false C 2.208,0.531 2.333,0.688 0.125,0.156 10 false B 2.521,0.531 2.646,0.688 0.125,0.156 10 false A 1.146,0.531 1.323,0.708 0.177,0.177 10 false *2 0.24,0.969 0.396,1.146 0.156,0.177 10 false *1 2.813,0.802 2.99,0.948 0.177,0.146 10 false *3 0.219,1.594 0.396,1.76 0.177,0.167 10 false *a 0.771,1.969 0.948,2.115 0.177,0.146 10 false D- 1.802,1.969 2.021,2.115 0.219,0.146 10 false D+ 0.583,2.281 0.75,2.438 0.167,0.156 10 false i1

Disconnect the instrument panel wire from the center airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
i1-2 (D+) - Body ground Engine switch on (IG) Below 1 V
i1-1 (D-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (D+) - i1-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (D+) - Body ground Always 1 MΩ or higher
i1-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (D+) - i1-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Steering Pad Assembly
*2 Spiral Cable Sub-assembly
*3 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Steering Pad Assembly)




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238229E01
0.366,1.282 0.522,1.433 0.156,0.152 10 *1 1.083,0.731 1.251,0.896 0.167,0.165 10 *2 2.618,1.008 2.792,1.164 0.174,0.156 10 *3 2.305,0.731 2.421,0.884 0.117,0.153 10 A 2.145,0.731 2.261,0.884 0.117,0.153 10 B 1.694,0.731 1.821,0.884 0.127,0.153 10 C 1.531,0.731 1.658,0.884 0.127,0.153 10 D 0.704,0.731 0.831,0.884 0.127,0.153 10 E 0.55,0.731 0.677,0.884 0.127,0.153 10 F 0.449,0.88 0.449,1.269 false

Connect the connectors to the steering pad assembly and center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Steering Pad Assembly
*2 Spiral Cable Sub-assembly
*3 Center Airbag Sensor Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire from the spiral cable sub-assembly.


U189555E01
0.332,0.532 0.442,0.685 0.109,0.153 10 F 0.655,0.532 0.776,0.685 0.121,0.153 10 E 1.491,0.532 1.612,0.685 0.121,0.153 10 D 1.81,0.532 1.931,0.685 0.121,0.153 10 C 2.26,0.532 2.380,0.685 0.121,0.153 10 B 2.572,0.532 2.692,0.685 0.121,0.153 10 A 1.049,0.532 1.226,0.708 0.177,0.175 10 *2 0.135,0.974 0.287,1.149 0.152,0.175 10 *1 2.882,0.816 3.058,0.960 0.176,0.144 10 *3 1.032,1.606 1.206,1.771 0.174,0.165 10 *a 2.382,2.886 2.558,3.034 0.177,0.148 10 D- 1.737,0.117 1.892,0.268 0.155,0.151 10 *4 0.22,0.68 0.22,0.965 false 1.669,2.886 1.878,3.037 0.209,0.151 10 D+ 2.03,2.504 1.8,2.855 false 2.233,2.504 2.463,2.855 false 2.087,0.536 2.087,0.204 2.087,0.204 1.921,0.204 false 1.248,1.998 1.539,2.173 0.291,0.175 10 G11

b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G11-1 (D+) - Body ground Engine switch on (IG) Below 1 V
G11-2 (D-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-1 (D+) - G11-2 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-1 (D+) - Body ground Always 1 MΩ or higher
G11-2 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-1 (D+) - G11-2 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Steering Pad Assembly
*2 Spiral Cable Sub-assembly
*3 Center Airbag Sensor Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)




OK

6.CHECK SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK SPIRAL CABLE SUB-ASSEMBLY
a.
U189554E02
0.229,0.677 0.229,0.958 false 2.094,0.677 2.094,0.958 false 1.281,2.052 0.99,2.052 true 1.781,2.052 1.49,2.052 true 0.344,0.531 0.448,0.688 0.104,0.156 10 false F 0.656,0.531 0.781,0.688 0.125,0.156 10 false E 1.49,0.531 1.615,0.688 0.125,0.156 10 false D 1.802,0.542 1.927,0.698 0.125,0.156 10 false C 2.25,0.531 2.375,0.688 0.125,0.156 10 false B 2.573,0.531 2.698,0.688 0.125,0.156 10 false A 1.01,0.531 1.188,0.708 0.177,0.177 10 false *2 0.135,0.969 0.292,1.146 0.156,0.177 10 false *1 2.875,0.813 3.052,0.958 0.177,0.146 10 false *3 0.229,1.594 0.406,1.76 0.177,0.167 10 false *a 0.771,1.958 0.948,2.104 0.177,0.146 10 false D- 2.01,0.979 2.167,1.156 0.156,0.177 10 false *4 1.802,1.969 2.021,2.115 0.219,0.146 10 false D+ 0.635,2.333 0.802,2.49 0.167,0.156 10 false i1

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
i1-2 (D+) - Body ground Engine switch on (IG) Below 1 V
i1-1 (D-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (D+) - i1-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (D+) - Body ground Always 1 MΩ or higher
i1-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-2 (D+) - i1-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*1 Steering Pad Assembly
*2 Spiral Cable Sub-assembly
*3 Center Airbag Sensor Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Steering Pad Assembly)




OK

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY