Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1815/54  Short in Front Passenger Side Squib 2nd Step Circuit  B1816/54  Open in Front Passenger Side Squib 2nd Step Circuit  B1817/54  Short to GND in Front Passenger Side Squib 2nd Step Circuit  B1818/54  Short to B+ in Front Passenger Side Squib 2nd Step Circuit  


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and front passenger airbag assembly.

The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC No. DTC Detection Condition Trouble Area
B1815/54
·

The center airbag sensor assembly detects a line short in the front passenger side squib 2nd step circuit during the primary check.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor assembly malfunction


·

Instrument panel wire

·

Instrument panel wire sub-assembly

·

Front passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1816/54
·

The center airbag sensor assembly detects an open in the front passenger side squib 2nd step circuit.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor assembly malfunction


B1817/54
·

The center airbag sensor assembly detects a short to ground in the front passenger side squib 2nd step circuit.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor assembly malfunction


B1818/54
·

The center airbag sensor assembly detects a short to B+ in the front passenger side squib 2nd step circuit.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor assembly malfunction



WIRING DIAGRAM

C351803E13
0.708,2.5 1.5,2.885 0.792,0.385 10 false V2 0.708,2.656 3.521,3.167 2.813,0.51 10 false Front Passenger Airbag Assembly (Front Passenger Side Squib 2nd Step) 2.083,1.885 2.875,2.271 0.792,0.385 10 false P2- 2.083,1.052 2.875,1.438 0.792,0.385 10 false P2+ 2.406,1.052 3.198,1.438 0.792,0.385 10 false 2 2.406,1.885 3.198,2.271 0.792,0.385 10 false 1 3.375,1.167 4.167,1.552 0.792,0.385 10 false GV1 4.5,1.042 5.292,1.427 0.792,0.385 10 false 1 4.5,1.885 5.292,2.271 0.792,0.385 10 false 2 4.708,3.188 6.729,3.406 2.021,0.219 10 false Center Airbag Sensor Assembly 4.719,3.021 5.51,3.406 0.792,0.385 10 false G19 3.375,2 4.167,2.385 0.792,0.385 10 false GV1 4.708,1.156 5.5,1.542 0.792,0.385 10 false P2+ 4.688,2 5.479,2.385 0.792,0.385 10 false P2- 3.417,0.969 4.208,1.354 0.792,0.385 10 false 3 3.448,1.813 4.24,2.198 0.792,0.385 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241746E06
0.191,1.439 0.347,1.591 0.156,0.152 10 *1 0.622,0.398 0.789,0.563 0.167,0.165 10 *3 2.713,1.146 2.887,1.302 0.174,0.156 10 *2 2.261,0.838 2.378,0.991 0.117,0.153 10 A 1.95,0.838 2.067,0.991 0.117,0.153 10 B 1.47,0.838 1.597,0.991 0.127,0.153 10 C 1.16,0.838 1.287,0.991 0.127,0.153 10 D 0.685,0.838 0.812,0.991 0.127,0.153 10 E 0.388,0.838 0.515,0.991 0.127,0.153 10 F 0.274,0.992 0.274,1.426 false 1.698,1.439 1.854,1.591 0.156,0.152 10 *4 1.781,0.992 1.781,1.426 false 0.982,0.86 0.982,0.487 0.982,0.487 0.818,0.487 false

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front passenger airbag assembly and center airbag sensor assembly. Also check that the connectors that link the instrument panel wire and instrument panel wire sub-assembly are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front passenger airbag assembly and center airbag sensor assembly. Also disconnect the instrument panel wire from the instrument panel wire sub-assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire sub-assembly connector (on the front passenger airbag assembly side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanisms of the instrument panel wire connector and instrument panel wire sub-assembly connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Passenger Airbag Assembly
*2 Center Airbag Sensor Assembly
*3 Instrument Panel Wire Sub-assembly
*4 Instrument Panel Wire



OK

2.CHECK FRONT PASSENGER AIRBAG ASSEMBLY

NG

REPLACE WIRE HARNESS

2.CHECK FRONT PASSENGER AIRBAG ASSEMBLY
a.
U189583E01
0.307,0.927 0.463,1.078 0.156,0.152 10 *1 1.824,2.625 1.980,2.776 0.156,0.152 10 *b 0.343,1.689 0.511,1.854 0.167,0.165 10 *a 2.071,2.192 2.381,2.343 0.310,0.151 10 SST 2.59,0.816 2.764,0.972 0.174,0.156 10 *2 2.172,0.507 2.289,0.660 0.117,0.153 10 A 2.016,0.507 2.132,0.660 0.117,0.153 10 B 1.526,0.507 1.653,0.660 0.127,0.153 10 C 1.369,0.507 1.496,0.660 0.127,0.153 10 D 0.892,0.507 1.019,0.660 0.127,0.153 10 E 0.494,0.507 0.621,0.660 0.127,0.153 10 F 0.39,0.654 0.39,0.914 false 1.759,2.279 2.038,2.279 false 1.514,2.705 1.793,2.705 false 0.451,2.21 0.656,2.366 0.205,0.156 10 V2

Connect the instrument panel wire to the instrument panel wire sub-assembly and center airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect a tester to the front passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1815/54, B1816/54, B1817/54 or B1818/54 is not output.


HINT:

Codes other than DTCs B1815/54, B1816/54, B1817/54 and B1818/54 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Front Passenger Airbag Assembly
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Passenger Airbag Assembly)
*b Color: Black



OK

NG

3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
a.
U189584E02
0.25,0.667 0.25,0.958 false 1.521,2.552 1.854,2.552 false 1.219,2.115 0.917,2.115 true 1.729,2.115 1.427,2.115 true 0.365,0.521 0.469,0.677 0.104,0.156 10 false F 0.792,0.521 0.917,0.677 0.125,0.156 10 false E 1.229,0.521 1.354,0.677 0.125,0.156 10 false D 1.385,0.521 1.51,0.677 0.125,0.156 10 false C 1.844,0.521 1.969,0.677 0.125,0.156 10 false B 2.26,0.521 2.385,0.677 0.125,0.156 10 false A 0.167,0.969 0.323,1.146 0.156,0.177 10 false *1 2.688,0.833 2.865,0.979 0.177,0.146 10 false *2 0.313,1.698 0.49,1.865 0.177,0.167 10 false *a 1.76,2.031 2.042,2.177 0.281,0.146 10 false P2+ 0.604,2.031 0.896,2.177 0.292,0.146 10 false P2- 1.875,2.458 2.031,2.604 0.156,0.146 10 false *b 0.552,2.344 0.76,2.5 0.208,0.156 10 false V2

Disconnect the instrument panel wire from the center airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V2-2 (P2+) - Body ground Engine switch on (IG) Below 1 V
V2-1 (P2-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (P2+) - V2-1 (P2-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (P2+) - Body ground Always 1 MΩ or higher
V2-1 (P2-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (P2+) - V2-1 (P2-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Passenger Airbag Assembly
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Passenger Airbag Assembly)
*b Color: Black




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238235E06
0.51,0.885 0.51,1.177 false 0.635,0.74 0.74,0.896 0.104,0.156 10 false F 0.792,0.74 0.917,0.896 0.125,0.156 10 false E 1.24,0.74 1.365,0.896 0.125,0.156 10 false D 1.396,0.74 1.521,0.896 0.125,0.156 10 false C 1.844,0.729 1.969,0.885 0.125,0.156 10 false B 2,0.729 2.125,0.885 0.125,0.156 10 false A 0.448,1.198 0.604,1.375 0.156,0.177 10 false *1 2.396,1.021 2.573,1.167 0.177,0.146 10 false *2

Connect the connectors to the front passenger airbag assembly and center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1815/54, B1816/54, B1817/54 or B1818/54 is not output.


HINT:

Codes other than DTCs B1815/54, B1816/54, B1817/54 and B1818/54 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Passenger Airbag Assembly
*2 Center Airbag Sensor Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
U189582E02
0.281,0.792 0.281,1.083 false 0.969,0.792 0.969,1.083 false 1.5,2.479 1.177,2.833 true 1.698,2.479 2.021,2.833 true 1.76,0.667 1.76,0.281 1.76,0.281 1.531,0.281 false 0.396,0.646 0.5,0.802 0.104,0.156 10 false F 0.677,0.646 0.802,0.802 0.125,0.156 10 false E 1.177,0.646 1.302,0.802 0.125,0.156 10 false D 1.448,0.646 1.573,0.802 0.125,0.156 10 false C 1.969,0.646 2.094,0.802 0.125,0.156 10 false B 2.24,0.646 2.365,0.802 0.125,0.156 10 false A 0.198,1.094 0.354,1.271 0.156,0.177 10 false *1 2.667,0.958 2.844,1.104 0.177,0.146 10 false *2 0.292,1.792 0.469,1.958 0.177,0.167 10 false *a 1.917,2.865 2.198,3.01 0.281,0.146 10 false P2- 0.885,1.094 1.042,1.271 0.156,0.177 10 false *3 1.021,2.865 1.302,3.01 0.281,0.146 10 false P2+ 1.344,0.198 1.5,0.375 0.156,0.177 10 false *4 0.458,2.24 0.76,2.396 0.302,0.156 10 false GV1

Disconnect the instrument panel wire sub-assembly from the instrument panel wire.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
GV1-3 (P2+) - Body ground Engine switch on (IG) Below 1 V
GV1-4 (P2-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GV1-3 (P2+) - GV1-4 (P2-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GV1-3 (P2+) - Body ground Always 1 MΩ or higher
GV1-4 (P2-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GV1-3 (P2+) - GV1-4 (P2-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Passenger Airbag Assembly
*2 Center Airbag Sensor Assembly
*3 Instrument Panel Wire Sub-assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Wire Sub-assembly)




OK

6.CHECK INSTRUMENT PANEL WIRE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE SUB-ASSEMBLY
a.
U189585E02
0.25,0.771 0.25,1.052 false 1.75,0.771 1.75,1.052 false 1.302,2.25 0.938,2.25 true 1.833,2.25 1.469,2.25 true 0.958,0.635 0.958,0.323 0.958,0.323 1.115,0.323 false 1.594,2.677 1.896,2.677 false 0.365,0.625 0.469,0.781 0.104,0.156 10 false F 0.635,0.625 0.76,0.781 0.125,0.156 10 false E 1.167,0.625 1.292,0.781 0.125,0.156 10 false D 1.438,0.625 1.563,0.781 0.125,0.156 10 false C 1.979,0.625 2.104,0.781 0.125,0.156 10 false B 2.25,0.625 2.375,0.781 0.125,0.156 10 false A 0.167,1.063 0.323,1.24 0.156,0.177 10 false *1 2.688,0.927 2.865,1.073 0.177,0.146 10 false *2 0.313,1.885 0.49,2.052 0.177,0.167 10 false *a 1.885,2.167 2.167,2.313 0.281,0.146 10 false P2+ 1.667,1.063 1.823,1.24 0.156,0.177 10 false *4 0.625,2.167 0.875,2.313 0.25,0.146 10 false P2- 1.146,0.229 1.302,0.406 0.156,0.177 10 false *3 1.927,2.604 2.083,2.75 0.156,0.146 10 false *b 0.583,2.469 0.781,2.625 0.198,0.156 10 false V2

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V2-2 (P2+) - Body ground Engine switch on (IG) Below 1 V
V2-1 (P2-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (P2+) - V2-1 (P2-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (P2+) - Body ground Always 1 MΩ or higher
V2-1 (P2-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V2-2 (P2+) - V2-1 (P2-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*1 Front Passenger Airbag Assembly
*2 Center Airbag Sensor Assembly
*3 Instrument Panel Wire Sub-assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Front Passenger Airbag Assembly)
*b Color: Black




OK

NG

REPLACE INSTRUMENT PANEL WIRE SUB-ASSEMBLY