Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor assembly and front seat outer belt assembly LH.

The center airbag sensor assembly uses this circuit to deploy the pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC No. DTC Detection Condition Trouble Area
B1905/74
·

The center airbag sensor assembly detects a line short in the front pretensioner squib LH circuit during the primary check.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor assembly malfunction


·

Floor wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Center airbag sensor assembly


B1906/74
·

The center airbag sensor assembly detects an open in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor assembly malfunction


B1907/74
·

The center airbag sensor assembly detects a short to ground in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor assembly malfunction


B1908/74
·

The center airbag sensor assembly detects a short to B+ in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Center airbag sensor assembly malfunction



WIRING DIAGRAM

C287107E88
0.698,2.677 2.813,3.104 2.115,0.427 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 0.708,2.51 1.229,2.802 0.521,0.292 10 false M11 4.688,3.188 6.688,3.427 2,0.24 10 false Center Airbag Sensor Assembly 4.688,3.031 5.063,3.292 0.375,0.26 10 false M9 2.094,1.052 2.708,1.25 0.615,0.198 10 false L+ 2.125,1.885 2.74,2.083 0.615,0.198 10 false L- 4.75,2 5.365,2.198 0.615,0.198 10 false PL- 4.729,1.146 5.344,1.344 0.615,0.198 10 false PL+ 2.438,1.052 2.594,1.25 0.156,0.198 10 false 1 2.438,1.896 2.594,2.094 0.156,0.198 10 false 2 4.5,1.052 4.656,1.25 0.156,0.198 10 false 2 4.531,1.896 4.688,2.094 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241752E06
0.637,0.972 0.758,1.125 0.121,0.153 10 D 1.044,0.972 1.164,1.125 0.121,0.153 10 C 1.622,0.972 1.743,1.125 0.121,0.153 10 B 2.025,0.972 2.146,1.125 0.121,0.153 10 A 2.47,0.979 2.646,1.154 0.177,0.175 10 *2 0.45,1.577 0.602,1.730 0.152,0.152 10 *1 0.526,1.119 0.526,1.56 false 1.638,0.473 1.790,0.625 0.152,0.152 10 *3 1.387,0.987 1.387,0.563 1.387,0.563 1.613,0.563 false

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly LH and center airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly LH and center airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the floor wire connector (on the front seat outer belt assembly LH side) is not loose, deformed or damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Center Airbag Sensor Assembly
*3 Floor Wire



OK

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH
a.
U189606E02
0.677,0.917 0.677,1.313 false 1.844,2.271 2.021,2.271 false 0.625,1.333 0.781,1.5 0.156,0.167 10 false *1 2.26,0.729 2.427,0.896 0.167,0.167 10 false *2 1.813,0.729 1.979,0.896 0.167,0.167 10 false A 1.646,0.729 1.813,0.896 0.167,0.167 10 false B 1.146,0.729 1.313,0.896 0.167,0.167 10 false C 0.771,0.729 0.938,0.896 0.167,0.167 10 false D 0.458,2.438 0.76,2.615 0.302,0.177 10 false M11 2.063,2.188 2.375,2.354 0.313,0.167 10 false SST 0.313,1.615 0.469,1.781 0.156,0.167 10 false *a

Connect the connector to the center airbag sensor assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector C.

Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Center Airbag Sensor Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
U189592E02
0.5,1 0.5,1.396 false 1.469,2.271 1.135,2.271 true 2.042,2.271 1.708,2.271 true 1.365,0.865 1.365,0.438 1.365,0.438 1.156,0.438 false 0.417,1.396 0.573,1.563 0.156,0.167 10 false *1 2.427,0.854 2.594,1.021 0.167,0.167 10 false *2 1.99,0.854 2.156,1.021 0.167,0.167 10 false A 1.594,0.854 1.76,1.021 0.167,0.167 10 false B 1.01,0.854 1.177,1.021 0.167,0.167 10 false C 0.615,0.854 0.781,1.021 0.167,0.167 10 false D 0.667,2.604 0.958,2.823 0.292,0.219 10 false M11 0.313,1.875 0.469,2.042 0.156,0.167 10 false *a 0.896,2.167 1.094,2.313 0.198,0.146 10 false L+ 2.073,2.188 2.271,2.333 0.198,0.146 10 false L- 0.958,0.354 1.125,0.521 0.167,0.167 10 false *3

Disconnect the floor wire from the center airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the engine switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M11-1 (L+) - Body ground Engine switch on (IG) Below 1 V
M11-2 (L-) - Body ground Engine switch on (IG) Below 1 V



iv.

Turn the engine switch off.


v.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (L+) - M11-2 (L-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (L+) - Body ground Always 1 MΩ or higher
M11-2 (L-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 (L+) - M11-2 (L-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)




OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238245E05
0.762,1.589 0.918,1.740 0.156,0.152 10 *1 2.147,0.987 2.322,1.143 0.174,0.156 10 *2 1.73,0.987 1.847,1.140 0.117,0.153 10 A 1.572,0.987 1.689,1.140 0.117,0.153 10 B 1.119,0.987 1.246,1.140 0.127,0.153 10 C 0.962,0.987 1.089,1.140 0.127,0.153 10 D 0.845,1.142 0.845,1.575 false

Connect the connectors to the front seat outer belt assembly LH and center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Outer Belt Assembly LH
*2 Center Airbag Sensor Assembly



OK

NG