Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1665/17  Center Floor Airbag Sensor Malfunction  


DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the center airbag sensor assembly and center floor airbag sensor.

The center floor airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbags should be deployed.

DTC B1665/17 is stored when a malfunction is detected in the center floor airbag sensor.

DTC No. DTC Detection Condition Trouble Area
B1665/17
·

Center floor airbag sensor malfunction

·

Center airbag sensor assembly malfunction


·

Center floor airbag sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

Refer to DTCs B1666/85 and B1667/85 (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>B1666/85).

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CENTER FLOOR AIRBAG SENSOR
a.
C358414E02
2.198,1.198 2.552,1.396 0.354,0.198 10 false A 2.615,0.927 2.969,1.125 0.354,0.198 10 false *2 2.042,1.198 2.396,1.396 0.354,0.198 10 false B 1.594,1.198 1.948,1.396 0.354,0.198 10 false C 1.438,1.198 1.792,1.396 0.354,0.198 10 false D 0.979,1.198 1.333,1.396 0.354,0.198 10 false E 0.833,1.198 1.188,1.396 0.354,0.198 10 false F 0.5,1.188 0.854,1.385 0.354,0.198 10 false *1

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the center floor airbag sensor with the rear floor airbag sensor and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1665/17 is output. A
DTC B1675/18 is output. B
DTC B1665/17 and B1675/18 are not output. C


HINT:

Codes other than DTC B1665/17 and B1675/18 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the center floor airbag sensor and rear floor airbag sensor to their original positions and connect the connectors.

Text in Illustration
*1 Rear Floor Airbag Sensor
*2 Center Airbag Sensor Assembly



A

B

C