Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  B2416  Height Control Sensor Malfunction  


DESCRIPTION

This DTC is stored when the headlight leveling ECU assembly detects a malfunction in the rear height control sensor sub-assembly LH power source or rear height control sensor sub-assembly LH.

DTC No. DTC Detecting Condition Trouble Area
B2416
·

Malfunction in rear height control sensor sub-assembly LH

·

Open or short in rear height control sensor sub-assembly LH power source circuit


·

Rear height control sensor sub-assembly LH

·

Harness or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

E223762E29
0.719,2.823 2.438,3.177 1.719,0.354 10 false Rear Height Control Sensor Sub-assembly LH 4.854,2.688 5.26,2.865 0.406,0.177 10 false A39 4.833,2.854 6.583,3.031 1.75,0.177 10 false Headlight Leveling ECU Assembly 4.771,1.417 4.979,1.615 0.208,0.198 10 false 21 4.771,2.073 4.979,2.292 0.208,0.219 10 false 12 1.604,0.865 2.042,1.031 0.438,0.167 10 false SHRR 1.688,2.188 2.104,2.365 0.417,0.177 10 false SHB 2.083,0.75 2.25,0.927 0.167,0.177 10 false 2 2.073,1.396 2.25,1.573 0.177,0.177 10 false 1 2.083,2.063 2.25,2.24 0.167,0.177 10 false 3 4.771,0.74 5.01,0.906 0.24,0.167 10 false 19 1.635,1.521 2.063,1.698 0.427,0.177 10 false SHG 5.021,0.854 5.406,1.052 0.385,0.198 10 false SHRL 5.031,2.198 5.438,2.354 0.406,0.156 10 false SBR 5.021,1.521 5.469,1.708 0.448,0.188 10 false SGR 0.708,2.646 1.125,2.823 0.417,0.177 10 false M12

CAUTION / NOTICE / HINT

NOTICE:

If any of the following are performed, initialization of the headlight leveling ECU assembly is necessary (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>INITIALIZATION).

·

Replacement of the headlight leveling ECU assembly.

·

Replacement or removal/installation of the rear height control sensor sub-assembly LH or work that changes the vehicle height such as replacement of suspension components.



PROCEDURE

1.CHECK FOR DTC

OK

NG

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the GTS.

HL AutoLeveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor power supply value / 0.00 to 5.00 V Approx. 5.00 V -

OK:

Normal condition listed above is displayed.




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor sub-assembly LH (See page Vehicle Interior>LIGHTING>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor sub-assembly LH (See page Vehicle Interior>LIGHTING>HEIGHT CONTROL SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH - HEADLIGHT LEVELING ECU ASSEMBLY)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the A39 headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M12-3 (SHB) - A39-12 (SBR) Always Below 1 Ω
M12-1 (SHG) - A39-21 (SGR) Always Below 1 Ω
M12-3 (SHB) or A39-12 (SBR) - Body ground Always 10 kΩ or higher
M12-1 (SHG) or A39-21 (SGR) - Body ground Always 10 kΩ or higher




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR