Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  B241A  Rear Height Control Sensor  


DESCRIPTION

The headlight leveling ECU assembly receives signals indicating the height of the vehicle from the rear height control sensor sub-assembly LH.

DTC No. DTC Detecting Condition Trouble Area
B241A
·

Malfunction in rear height control sensor sub-assembly LH

·

Open or short in rear height control sensor sub-assembly LH circuit


·

Rear height control sensor sub-assembly LH

·

Harness or connector

·

Headlight leveling ECU assembly



WIRING DIAGRAM

E256782E40
2.438,0.656 2.896,0.854 0.458,0.198 10 false SHB 2.438,1.281 2.896,1.479 0.458,0.198 10 false SHG 2.844,0.542 3.063,0.74 0.219,0.198 10 false 3 2.844,1.177 3.063,1.375 0.219,0.198 10 false 1 4.063,0.542 4.281,0.74 0.219,0.198 10 false 12 4.063,1.188 4.281,1.385 0.219,0.198 10 false 21 4.365,0.656 4.688,0.865 0.323,0.208 10 false SBR 4.354,1.281 4.813,1.479 0.458,0.198 10 false SGR 0.76,1.833 1.219,2.031 0.458,0.198 10 false M12 4.208,2 6.969,2.313 2.76,0.313 10 false Headlight Leveling ECU Assembly 4.219,1.854 4.677,2.052 0.458,0.198 10 false A39 0.76,2.021 3.615,2.281 2.854,0.26 10 false Rear Height Control Sensor Sub-assembly LH

CAUTION / NOTICE / HINT

NOTICE:

If any of the following are performed, initialization of the headlight leveling ECU assembly is necessary (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>INITIALIZATION).

·

Replacement of the headlight leveling ECU assembly.

·

Replacement or removal/installation of the rear height control sensor sub-assembly LH or work that changes the vehicle height such as replacement of suspension components.



PROCEDURE

1.CHECK FOR DTC

OK

NG

2.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the GTS.

HL AutoLeveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Height Sens Pw Supply Val Rear height control sensor power supply value / 0.00 to 5.00 V Approx. 5.00 V -
Rr Height Sens Signal Val Rear height control sensor signal value / 0.00 to 5.00 V Approx. 2.50 V (When the vehicle is level) Value changes according to vehicle height

OK:

Normal conditions listed above are displayed.




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH
a.

Remove the rear height control sensor sub-assembly LH (See page Vehicle Interior>LIGHTING>HEIGHT CONTROL SENSOR>REMOVAL).


b.

Inspect the rear height control sensor sub-assembly LH (See page Vehicle Interior>LIGHTING>HEIGHT CONTROL SENSOR>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH - HEADLIGHT LEVELING ECU ASSEMBLY)

NG

REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH - HEADLIGHT LEVELING ECU ASSEMBLY)
a.

Disconnect the A39 headlight leveling ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M12-3 (SHB) - A39-12 (SBR) Always Below 1 Ω
M12-1 (SHG) - A39-21 (SGR) Always Below 1 Ω
M12-3 (SHB) or A39-12 (SBR) - Body ground Always 10 kΩ or higher
M12-1 (SHG) or A39-21 (SGR) - Body ground Always 10 kΩ or higher




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR