Home › Vehicle Interior › ENGINE HOOD / DOOR › FRONT DOOR › 2014.09–2016.05
RM24M0E _58 Vehicle Interior _059569 ENGINE HOOD / DOOR _0292026 FRONT DOOR A

ENGINE HOOD / DOOR  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL FRONT DOOR MUDGUARD SUB-ASSEMBLY (for Standard)

Hide 2.INSTALL FRONT DOOR MUDGUARD SUB-ASSEMBLY (for Sport Package)

Hide 67663D 3.INSTALL DOOR FRAME GARNISH LH

B144424

a.

Attach the claw to install the garnish.


Hide 82152 4.INSTALL FRONT DOOR WIRE LH

a.
B136633

Install the wire with the 2 bolts.

Torque:
Reference : 8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

In order to prevent water leakage, be sure that the lip of the rubber grommet does not turn up or is not deformed when installing the wire.



b.

Connect the wire clips.


Hide 67862 5.INSTALL FRONT DOOR WEATHERSTRIP LH

a.

Attach the clips to install the weatherstrip.


Hide 68620 6.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.
B136632E02
3.104,0.75 2.75,1.708 true 2.438,1.75 3.083,2.021 0.646,0.271 10 true Adhesive

Apply MP grease to the sliding area of the door check.


b.

Install the door check to the door panel with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Install the door check so that the rivet head is up.



c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1344 or equivalent



d.

Install the door check to the body with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 69202A 7.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.
B142914E02
2.156,1.094 1.99,1.427 1.99,1.427 1.99,1.688 false 1.896,1.094 1.448,1.313 1.448,1.313 1.448,1.49 false 2.375,0.75 2.469,0.313 false 2.469,0.313 2.542,0.313 false 2,0.448 2.323,0.448 false 2.323,0.448 2.198,0.635 false 1.438,3.833 2.271,4.229 2.271,4.229 2.375,4.229 false 0.063,0.031 0.74,0.208 0.677,0.177 10 false Outside: 0.063,1.865 0.74,2.042 0.677,0.177 10 false Inside: 2.594,0.24 3.052,0.438 0.458,0.198 10 false Frame 1.833,1.708 2.125,1.906 0.292,0.198 10 false Nut 1.198,1.49 1.615,1.688 0.417,0.198 10 false Cover 1.146,0.354 1.906,0.521 0.76,0.167 10 false Door Panel 2.635,3.396 3.01,3.542 0.375,0.146 10 false Slide 2.427,4.146 3.146,4.292 0.719,0.146 10 false Open Rod 0.229,0.385 0.604,0.531 0.375,0.146 10 false Slide

Install the open rod to the outside handle frame.


b.

Slide the outside handle frame in the direction indicated by the arrow in the illustration.


c.

Using a T30 "TORX" socket, install the outside handle frame with the screw.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

Insert a cover between the nut and the door panel.



d.

Install the outside handle pads front and rear.


e.

w/ Entry Function:

Connect the connector.


Hide 69220 8.INSTALL FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH

a.
B142937

Install the outside handle by pushing in the direction indicated by the arrow in the illustration.

NOTICE:

If the release plate is not pulled and held when installing the outside handle, it will strike against the outside handle and become damaged.



b.

w/ Entry Function:

Connect the connector.


Hide 69040A 9.INSTALL FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH

a.

Apply MP grease to the sliding and rotating areas of the door lock.


b.

Install a new door lock wire harness packing to the door lock.

NOTICE:
·

When reusing a door lock that has been removed, replace the packing in the connecting part with new packing.

·

Be careful that no grease or dirt sticks to the packing surface in the connecting part.

·

Reusing removed packing or using damaged packing will allow water to penetrate through to the connecting part, resulting in a malfunction of the door lock.




c.
B065961

Insert the open rod into the lock and then set it to the door panel.

NOTICE:

Make sure that the outside handle link is securely engaged with the door lock.



d.
B136629

Apply adhesive to the threads of the screws.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1344 or equivalent



e.

Using a T30 "TORX" socket, install the lock with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


f.

Connect the lock connector.


Hide 69217D 10.INSTALL FRONT DOOR OUTSIDE HANDLE COVER

a.
B136628

Using a T30 "TORX" socket, install the outside handle cover with the screw.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Install the hole plug.


Hide 67404F 11.INSTALL FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER LH

a.
B136627

Install the frame with the bolt.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)


Hide 85720C 12.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

Using a T25 "TORX" driver, install the regulator motor with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Do not rotate the motor counterclockwise until the window glass installation is completed.



Hide 69802 13.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B136638

Apply MP grease to the sliding and rotating parts of the window regulator.

NOTICE:

Do not apply grease to the spring of the window regulator.



b.
B136626

Install the window regulator with the 6 bolts.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)

NOTICE:

Be careful not to drop the door window regulator as it may become damaged.



c.

Connect the window regulator connector.


Hide 68102 14.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

NOTICE:

Do not damage the door glass.


a.
B142916

Install the glass run.


b.

Insert the door glass into the door panel along the glass run in the direction indicated by the arrow in the illustration.


c.
B136624

Install the door glass to the window regulator with the 2 bolts.

Torque:
7.5 N*m (77 kgf*cm, 66 in.*lbf)



e.

Inspect the operation of the power window.

HINT:

When the installation point of the door glass does not match, adjust the regulator position using manual operation.


i.

Connect the power window switch to the wire harness and turn the engine switch on (IG).


ii.

Repeat the UP and DOWN operations several times using manual operation.



Hide 87940 15.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

a.
B136623

Install the mirror with the 3 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the mirror connector.


Hide 67832 16.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.
B136643E01
0.082,1.097 0.513,1.417 0.431,0.320 10 Butyl Tape 1.275,1.176 0.549,1.176 false

Apply butyl tape to the door panel, as shown in the illustration.


b.

Install the service hole cover.

HINT:
·

When installing the service hole cover, pull out the links and connectors through the service hole cover.

·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, confirm the sealing condition.




c.
B136622

Connect the connectors and clamps.


d.

Install the No. 1 reinforcement with the 2 screws.


Hide 67602 17.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.

Install the inside handle with the 3 screws.


b.
B148623E01
0.407,3.127 0.809,3.276 0.402,0.149 10 Claws

Attach the 7 claws to install the weatherstrip inner.


c.
U188548

Connect the 2 cables to the inside handle, as shown in the illustration.


d.
B136621

Attach the 9 clips to install the trim board.


e.

Install the 2 screws.


f.

Install the 2 cushion rubbers.


g.
B142917

Attach the claw to install the cover.


Hide 84040 18.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

a.
B148621

Install the switch to the panel with the 3 screws.


Hide 84810 19.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Passenger Side)

a.
B148622E02
0.427,1.917 1.042,2.115 0.615,0.198 10 false Claw

Attach the 2 claws to install the switch to the panel.


Hide 74232 20.INSTALL FRONT ARMREST BASE PANEL UPPER LH

a.
B148620E01
0.44,3.188 0.777,3.333 0.336,0.145 10 Claw

Connect the connector and install the switch to the panel.


b.

Attach the 10 claws to install the panel.


Hide 69278B 21.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH

B136619

a.

Attach the 3 claws to install the bezel plug.


Hide 67492A 22.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

B136618

a.

Attach the clip and claw to install the garnish.


Hide 28800 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 24.PERFORM INITIALIZATION

a.

Perform initialization (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.



Hide 25.CHECK SRS WARNING LIGHT