Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P2767  Input / Turbine Speed Sensor "B" Circuit No Signal  


DESCRIPTION

The ECM detects the input shaft rotation speed based on the signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) and performs gear ratio control.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P2767
1.

The vehicle is driven with the shift lever in D, the output shaft speed is 300 rpm or more and the vehicle speed is approx. 7 km/h (4.3 mph).

2.

The transmission revolution sensor (NIN) value is less than 300 rpm.

3.

2 seconds

4.

1 trip detection logic


·

Open or short in transmission revolution sensor (NIN) circuit

·

Transmission revolution sensor (NIN)

·

ECM

·

Continuously variable transaxle assembly



MONITOR DESCRIPTION

The ECM receives a signal from the primary pulley speed sensor (transmission revolution sensor (NIN)) installed in the continuously variable transaxle and determines the input shaft speed in order to control the gear ratio. If the ECM detects no signal from the primary pulley speed sensor even while the vehicle is moving, it will conclude that there is a malfunction in the primary pulley speed sensor. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C200870E26
5.792,2.927 6.104,3.125 0.313,0.198 10 false D2 5.792,3.104 6.177,3.302 0.385,0.198 10 false ECM 5.604,1.24 6.021,1.438 0.417,0.198 10 false NIN+ 5.25,2.344 5.531,2.542 0.281,0.198 10 false 102 5.26,1.365 5.563,1.563 0.302,0.198 10 false 101 5.615,2.198 6.104,2.396 0.49,0.198 10 false NIN- 2.333,1.125 2.688,1.323 0.354,0.198 10 false NIN+ 2.75,2.333 2.979,2.531 0.229,0.198 10 false 1 2.75,1.354 2.948,1.552 0.198,0.198 10 false 2 2.333,2.083 2.708,2.281 0.375,0.198 10 false NIN- 0.76,2.708 1.073,2.906 0.313,0.198 10 false D64 0.76,2.885 3.177,3.083 2.417,0.198 10 false Transmission Revolution Sensor (NIN)

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SPD (NIN))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NIN) Primary pulley speed (NIN)/
min.: 0 rpm
max.: 12750 rpm
·

Vehicle stopped: 0 rpm

·

Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed


Data is displayed in increments of 50 rpm.

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN) (RESISTANCE)

B

4.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN) (RESISTANCE)
a.
C200614E01
0.057,0.004 0.298,0.206 0.240,0.202 10 *1 1.304,1.683 1.604,1.17 false 1.081,1.709 1.527,1.911 0.446,0.202 10 NIN+ 2.152,1.683 1.853,1.17 false 2.046,1.709 2.492,1.911 0.446,0.202 10 NIN-

Disconnect the transmission revolution sensor (NIN) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω


Text in Illustration
*1 Component without harness connected
(Transmission Revolution Sensor (NIN))



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)

NG

6.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN) (SENSOR TIP)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NIN) - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D2-102 (NIN-) - D2-101 (NIN+) 20°C (68°F) 560 to 680 Ω
D2-102 (NIN-) - Body ground Always 10 kΩ or higher
D2-101 (NIN+) - Body ground Always 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION
6.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN) (SENSOR TIP)
a.

Remove the transmission revolution sensor (NIN).


b.

Check the sensor tip of the transmission revolution sensor (NIN).

OK:

The sensor tip of the transmission revolution sensor (NIN) is not damaged or contaminated.


HINT:

If the sensor tip of the transmission revolution sensor (NIN) is damaged or contaminated with metal particles, the CVT belt may be damaged.




OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NIN)

NG

7.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
7.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NEXT

8.PERFORM INITIALIZATION