Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0741  Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL)  P2757  Torque Converter Clutch Pressure Control Solenoid Control Circuit Performance (Shift Solenoid Valve DSU)  


DESCRIPTION

The ECM uses shift solenoid valves SL and DSU to perform lock-up control in response to the driving conditions.

NOTICE:

If any parts inside the torque converter assembly are damaged, DTC P0741/64 and P2757/64 could be output. In this case, make sure to replace both the torque converter assembly and the continuously variable transaxle assembly as broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.


HINT:

Shift solenoid valve DSU controls the lock-up clutch pressure in response to the input torque.


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0741
1.

The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift lever in D.

2.

The lock-up signal is on, but lock-up is off.

3.

-

4.

2 trip detection logic


·

Continuously variable transaxle assembly

·

torque converter assembly


P2757
1.

The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift lever in D.

2.

The lock-up signal is on, but lock-up is off.

3.

-

4.

2 trip detection logic


1.

The engine is warmed up, and the vehicle is driven at a speed of 10 km/h (6.0 mph) or more with the shift lever in D.

2.

The lock-up signal is off, but lock-up is on.

3.

-

4.

2 trip detection logic



MONITOR DESCRIPTION

When performing lock-up control (on/off) of the torque converter, the ECM compares the rotating speeds of the turbine (NT) and engine (NE) to detect mechanical malfunctions in the shift solenoid valves SL and DSU. When the rotating speeds are different than expected, the ECM detects the problem, illuminates the MIL and stores the DTC.

PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0741 AND P2757)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
Only P0741 and/or P2757 is output A
P0741 and/or P2757 and other DTCs are output B

HINT:

If any other DTCs besides P0741 or P2757 are output, perform troubleshooting for those DTCs first.




A

2.CLEAR DTC

B

2.CLEAR DTC

NEXT

3.PERFORM DRIVE TEST
3.PERFORM DRIVE TEST
CAUTION:

Strictly observe posted speed limits, traffic laws and road conditions when performing the road test.


NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform the test with the A/C off and no electrical load.

·
C246168E03
2.281,1.708 2.396,1.708 2.396,1.708 2.552,1.177 true 3,1.729 2.833,1.729 2.833,1.729 2.615,0.979 true 2.031,0.146 2.198,0.302 0.167,0.156 10 false *a 3.042,1.615 3.208,1.771 0.167,0.156 10 false *b 2.125,1.625 2.292,1.781 0.167,0.156 10 false *1

Make sure to replace both the torque converter assembly and the continuously variable transaxle assembly if any parts inside the torque converter assembly are damaged. Broken pieces may have entered through the oil passages and some of them may be present in the continuously variable transaxle assembly.



Text in Illustration
*1 Oil seal
*a Example of the damage
*b Damage

HINT:
·

Lock-up control will not operate when the CVT fluid temperature is 40°C (104°F) or less and the vehicle speed is 60 km/h (37 mph) or less, or when the CVT fluid temperature is 5°C (41°F) or less.

·

Lock-up control will not operate when the engine coolant temperature is 30°C (86°F) or less.

·

The lock-up off vehicle speed may vary depending on the electrical load, air conditioning and brake operations.



a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / SPD (NT), Lock Up and Engine Speed.


e.

Check the Data List while driving.

Result
Result Proceed to
When the lock-up is on, the turbine speed is lower than the engine speed. A
When the lock-up is off, the turbine speed is equal to the engine speed.
When the lock-up is on, the turbine speed is equal to the engine speed. B
When the lock-up is off, the turbine speed is lower than the engine speed.



A

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

B

4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
4.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NEXT

5.REPLACE TORQUE CONVERTER ASSEMBLY
5.REPLACE TORQUE CONVERTER ASSEMBLY

NEXT

6.PERFORM INITIALIZATION