Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate sensor.

HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P1585
1.

The engine switch is on (IG).

2.

The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

3.0 seconds

4.

1 trip detection logic


·

Yaw rate sensor

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system


1.

The engine switch is on (IG).

2.

The power source voltage to the yaw rate sensor remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

No signal from the yaw rate sensor is detected 7 times or more.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

A yaw rate sensor power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.

3.

3.0 seconds

4.

1 trip detection logic



WIRING DIAGRAM

C204216E05
5.815,2.938 6.204,3.140 0.390,0.202 10 ECM 1.883,2.908 3.052,3.110 1.169,0.202 10 Yaw Rate Sensor 1.642,1.351 3.332,1.712 1.691,0.361 10 Brake Actuator Assembly (Skid Control ECU) 0.395,3.364 2.234,3.565 1.840,0.202 10 : CAN Communication Line

PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs of the CAN communication system (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING INTELLIGENT TESTER (G SENSOR)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.READ VALUE USING INTELLIGENT TESTER (G SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
G sensor Converted output voltage of G sensor/
min.: 0 V
max.: 5 V
Displays converted voltage of G sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

3.REPLACE YAW RATE SENSOR

B

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

3.REPLACE YAW RATE SENSOR

NEXT

4.PERFORM INITIALIZATION