Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1589  Acceleration Sensor Learning Value  


DESCRIPTION

The ECM stores DTC P1589 if the ECM or other components are replaced that require the yaw rate sensor or deceleration sensor to be calibrated (deceleration sensor zero point calibration) and calibration is terminated or the vehicle is driven before calibration is complete.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P1589
1.

The vehicle speed is 2 km/h (1.2 mph) or more.

2.

Deceleration sensor 0 point calibration has not been completed.

3.

-

4.

1 trip detection logic


Deceleration sensor zero point calibration has not been performed
1.

Deceleration sensor zero point calibration is performed.

2.

The learned values of the deceleration sensor zero point calibration are abnormal (out of normal range).

3.

-

4.

1 trip detection logic


·

Vehicle was not stabilized during deceleration sensor zero point calibration

·

Deceleration sensor*1

·

Yaw rate sensor*2

·

ECM



·

*1: w/o VSC

·

*2: w/ VSC


PROCEDURE

1.PERFORM INITIALIZATION (DECELERATION SENSOR 0 POINT CALIBRATION)
NOTICE:
·

If CVT oil pressure calibration is performed before deceleration sensor zero point calibration, DTC P1589 is stored. In this case, perform the steps below to return the system to normal.

·

Always perform zero point calibration with the vehicle on level ground.

·

Do not shake or vibrate the vehicle during zero point calibration.



a.

Turn the engine switch off.


b.

Move the shift lever to P and apply the parking brake.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Deceleration Sensor 0 Point Calibration.

HINT:
·

When "Complete" is displayed on the intelligent tester, deceleration sensor zero point calibration is completed.

·

If "Error" is displayed on the intelligent tester, the yaw rate sensor circuit may have a malfunction.

·

Shaking or vibrating the vehicle during zero point calibration may cancel the calibration. If "Error" is displayed on the intelligent tester, perform deceleration sensor zero point calibration again.




g.

If "Error" is displayed on the intelligent tester, read the DTCs using the intelligent tester.

Result
Result Proceed to
Deceleration sensor zero point calibration is completed normally A
DTC P1589 is output (w/ VSC) B
DTC P1589 is output (w/o VSC) C



A

2.PERFORM INITIALIZATION (CVT OIL PRESSURE CALIBRATION)

B

3.INSPECT YAW RATE SENSOR

C

7.INSPECT DECELERATION SENSOR
2.PERFORM INITIALIZATION (CVT OIL PRESSURE CALIBRATION)
NOTICE:

Do not initialize the learned values by performing reset memory.


a.

Turn the engine switch off and wait at least 30 seconds.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG) and wait at least 2 seconds.

NOTICE:

Do not start the engine.


HINT:

CVT oil pressure calibration is performed with the engine switch on (IG) (engine stopped). However, calibration cannot be performed under the following conditions:

·

When the oil pressure sensor value is 0.065 MPa or more

·

When the CVT oil temperature is -5°C (23°F) or less or 100°C (212°F) or more




d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility.


f.

Start the engine and wait at least 5 seconds.

NOTICE:
·

Start the engine with the shift lever in P.

·

After starting the engine, do not operate the accelerator pedal.




g.

Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.

HINT:
·

During CVT oil pressure calibration, the engine idle speed will increase.

·

When "Complete" is displayed on the intelligent tester, CVT oil pressure calibration is completed.

·

The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.




h.

Check that no DTC is stored.



NEXT

END

3.INSPECT YAW RATE SENSOR
a.

Check the yaw rate sensor for any inclination, bracket deformation or installation clearance.

OK:

The yaw rate sensor is installed correctly.




OK

4.READ VALUE USING INTELLIGENT TESTER (G SENSOR)

NG

4.READ VALUE USING INTELLIGENT TESTER (G SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
G sensor Converted output voltage of G sensor/
min.: 0 V
max.: 5 V
Displays converted voltage of G sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

5.REPLACE YAW RATE SENSOR

B

11.REPLACE ECM
5.REPLACE YAW RATE SENSOR

NEXT

6.PERFORM INITIALIZATION
7.INSPECT DECELERATION SENSOR
a.

Check the deceleration sensor for any inclination, bracket deformation or installation clearance.

OK:

The deceleration sensor is installed correctly.




OK

8.READ VALUE USING INTELLIGENT TESTER (G SENSOR)

NG

SECURELY INSTALL OR REPLACE DECELERATION SENSOR

8.READ VALUE USING INTELLIGENT TESTER (G SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
G sensor Converted output voltage of G sensor/
min.: 0 V
max.: 5 V
Displays converted voltage of G sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

9.REPLACE DECELERATION SENSOR

B

11.REPLACE ECM
9.REPLACE DECELERATION SENSOR

NEXT

10.PERFORM INITIALIZATION
11.REPLACE ECM

NEXT

12.PERFORM INITIALIZATION