Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the yaw rate sensor or deceleration sensor.

HINT:

If a CAN communication DTC is output, perform troubleshooting for that DTC first.


w/o VSC:
DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P1585
1.

The engine switch is on (IG).

2.

The output value of the deceleration sensor remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

3.0 seconds

4.

1 trip detection logic


·

Deceleration sensor

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system


1.

The engine switch is on (IG).

2.

The power source voltage to the deceleration sensor remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

No signal from the deceleration sensor is detected 7 times or more.

3.

3.0 seconds

4.

1 trip detection logic



w/ VSC:
DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P1585
1.

The engine switch is on (IG).

2.

The output value of the yaw rate sensor remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

3.

3.0 seconds

4.

1 trip detection logic


·

Yaw rate sensor

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system


1.

The engine switch is on (IG).

2.

The power source voltage to the yaw rate sensor remains at 4.4 V or less, or 5.6 V or higher for at least 1.2 seconds.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

No signal from the yaw rate sensor is detected 7 times or more.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

3.

3.0 seconds

4.

1 trip detection logic


1.

The engine switch is on (IG).

2.

A yaw rate sensor power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.

3.

3.0 seconds

4.

1 trip detection logic



WIRING DIAGRAM

C229195E01
5.771,1.709 6.160,1.911 0.390,0.202 10 ECM 0.568,1.806 1.928,2.008 1.360,0.202 10 Deceleration Sensor 2.85,1.784 4.540,2.145 1.691,0.361 10 Brake Actuator Assembly (Skid Control ECU) 0.711,2.397 2.551,2.599 1.840,0.202 10 : CAN Communication Line 5.583,1.145 6.026,1.347 0.443,0.202 10 CANH 5.583,0.663 6.014,0.809 0.430,0.145 10 CANL 3.6,1.149 4.042,1.351 0.443,0.202 10 CANH 3.6,0.667 4.030,0.813 0.430,0.145 10 CANL 3.259,0.586 3.573,0.750 0.314,0.163 10 GL1 3.259,0.958 3.710,1.120 0.451,0.162 10 GGND 3.259,1.31 3.608,1.465 0.349,0.156 10 VGS 1.311,0.578 1.625,0.741 0.314,0.163 10 GL1 1.171,0.95 1.622,1.111 0.451,0.162 10 GGND 1.269,1.301 1.618,1.457 0.349,0.156 10 VGS 0.049,0.016 0.841,0.262 0.792,0.246 12 w/o VSC: 0.558,1.663 0.907,1.819 0.349,0.156 10 N38 1.74,1.206 1.873,1.397 0.134,0.191 10 1 1.74,0.493 1.873,0.684 0.134,0.191 10 2 1.74,0.858 1.873,1.049 0.134,0.191 10 3 2.852,1.639 3.118,1.845 0.266,0.206 10 A22 2.952,0.493 3.173,0.656 0.221,0.163 10 21 2.952,0.858 3.173,1.021 0.221,0.163 10 14 2.952,1.206 3.173,1.369 0.221,0.163 10 24

C204216E07
1.656,1.375 3.302,1.854 1.646,0.479 10 false Brake Actuator Assembly (Skid Control ECU) 5.792,2.969 6.208,3.24 0.417,0.271 10 false ECM 0.385,3.406 2.26,3.625 1.875,0.219 10 false : CAN Communication Line 1.885,2.938 3.031,3.219 1.146,0.281 10 false Yaw Rate Sensor 0.125,0.125 1.198,0.323 1.073,0.198 12 false w/ VSC:

PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)
a.

Check for DTCs of the CAN communication system (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING INTELLIGENT TESTER (G SENSOR)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.READ VALUE USING INTELLIGENT TESTER (G SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
G sensor Converted output voltage of G sensor/
min.: 0 V
max.: 5 V
Displays converted voltage of G sensor
·

Vehicle on level ground: 2.31 V to 2.69 V

·

Decelerating: 1.88 V to 2.5 V

·

Accelerating: 2.5 V to 3.11 V

·

G sensor malfunction: Set to 1.87 V

·

Communication malfunction: Set to 1.87 V


-

Result
Result Proceed to
Data displayed is not as specified under Normal Condition
(w/o VSC)
A
Data displayed is as specified under Normal Condition
(w/o VSC)
B
Data displayed is not as specified under Normal Condition
(w/ VSC)
C
Data displayed is as specified under Normal Condition
(w/ VSC)
D



A

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DECELERATION SENSOR)

B

6.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

C

10.REPLACE YAW RATE SENSOR

D

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DECELERATION SENSOR)
a.

Disconnect the brake actuator assembly connector.


b.

Disconnect the deceleration sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-24(VGS) - N38-1(VGS) Always Below 1 Ω
A22-21(GL1) - N38-2(GL1) Always Below 1 Ω
A22-14(GGND) - N38-3(GGND) Always Below 1 Ω
A22-24(VGS) or N38-1(VGS) - Body ground and other terminals Always 10 kΩ or higher
A22-21(GL1) or N38-2(GL1) - Body ground and other terminals Always 10 kΩ or higher
A22-14(GGND) or N38-3(GGND) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the brake actuator assembly connector.


e.

Connect the deceleration sensor connector.



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE OF DECELERATION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE OF DECELERATION SENSOR)
a.
U189436E02
1.458,1.219 0.99,1.646 0.99,1.646 0.844,1.646 false 0.333,1.021 0.604,1.198 0.271,0.177 10 false N38 0.094,0.083 0.313,0.271 0.219,0.188 10 false *a 0.5,1.563 0.833,1.75 0.333,0.188 10 false VGS

Check that the deceleration sensor is properly installed and the connector is securely connected.


b.

Disconnect the deceleration sensor connector.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N38-1(VGS) - Body ground Engine switch on (IG) 4.75 to 5.25 V


Text in Illustration
*a Front view of wire harness connector
(to Deceleration Sensor)



OK

5.CHECK DECELERATION SENSOR (GL1 VOLTAGE)

NG

6.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
5.CHECK DECELERATION SENSOR (GL1 VOLTAGE)
a.
U189196E02
1.531,1.167 1.115,1.74 1.115,1.74 0.99,1.74 true 1.708,1.104 1.073,0.594 1.073,0.594 0.99,0.594 true 0.156,0.146 0.396,0.302 0.24,0.156 10 false *1 0.469,1.031 0.74,1.208 0.271,0.177 10 false N38 0.563,1.667 1.042,1.854 0.479,0.188 10 false GGND 0.698,0.521 1.021,0.708 0.323,0.188 10 false GL1

Remove the deceleration sensor and check the connector case for deformation or corrosion.


b.

Connect 3 dry cell batteries of 1.5 V in series.


c.

Connect the positive (+) lead from the batteries to terminal 1 (VGS) and the negative (-) lead to terminal 3 (GGND) to apply a voltage of 4.5 V.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N38-2(GL1) - N38-3(GGND) 4.5 V applied across terminals 1(VGS) and 3 (GGND), and sensor on level ground Approx. 2.3 V
N38-2(GL1) - N38-3(GGND) 4.5 V applied across terminals 1(VGS) and 3 (GGND), and sensor tilted forward and rearward Changes between approx. 0.7 to 4.0


Text in Illustration
*1 Deceleration Sensor


NOTICE:
·

Do not apply 6 V or more across terminals 1 (VGS) and 3 (GGND).

·

If the sensor is tilted too much, wrong values may be output.

·

If the sensor has been dropped, replace it with a new one.




OK

6.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

8.REPLACE DECELERATION SENSOR
6.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NEXT

7.PERFORM INITIALIZATION
8.REPLACE DECELERATION SENSOR

NEXT

9.PERFORM INITIALIZATION
10.REPLACE YAW RATE SENSOR

NEXT

11.PERFORM INITIALIZATION