Home › Drivetrain › K112 (CVT) › TRANSMISSION CONTROL CABLE › 2013.04–2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292051 TRANSMISSION CONTROL CABLE N

K112 CVT  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT SHIFT LEVER POSITION

a.

When moving the shift lever from P to R with the engine switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.


b.

Start the engine and make sure that the vehicle moves forward when moving the shift lever from N to D and moves rearward when moving the lever to R.

If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.


Hide 2.ADJUST SHIFT LEVER POSITION

a.

Apply the parking brake and move the shift lever to N.


b.

Remove the instrument cluster finish panel assembly and center instrument cluster finish panel sub-assembly (See page Drivetrain>K112 (CVT)>TRANSMISSION CONTROL CABLE>REMOVAL).


c.
C133003

Disconnect the end of the transmission control cable assembly from the shift lever assembly.


d.
C264709E01
0.639,0.538 0.857,0.707 0.218,0.170 10 *1 1.514,0.881 0.828,0.624 false

Pull out the stopper of the transmission control cable.

Text in Illustration:
*1 Stopper

NOTICE:

Do not remove the stopper. If the stopper is removed, reinstall it to its original position.



e.
C264710E01
0.168,2.468 0.366,2.646 0.199,0.178 10 *1 1.199,1.523 0.63,2.558 0.63,2.558 0.393,2.558 false

Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.

Text in Illustration:
*1 Nut

NOTICE:

Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.



f.
C367599E01
1.813,3.76 2.406,3.135 2.406,3.135 1.74,2.333 false 0.115,0.083 0.354,0.313 0.24,0.229 10 false *a 1.188,0.167 1.427,0.396 0.24,0.229 10 false *c 0.458,1.583 0.698,1.813 0.24,0.229 10 false *b 2.458,3.052 2.698,3.281 0.24,0.229 10 false *1 2.073,0.188 2.313,0.417 0.24,0.229 10 false *c 1.635,1.583 1.875,1.813 0.24,0.229 10 false *c 1.646,2.604 1.885,2.833 0.24,0.229 10 false *c

Push the 2 claws together at the top of the transmission control cable lock piece. While holding the 2 claws together, push the 2 lugs on the bottom of the lock piece toward each other and upward to pull out the lock piece.

Text in Illustration
*1 Lock Piece
*a Side View
*b Bottom View
*c Push


g.

Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.

C200365E21
1.219,0.625 1.313,0.385 1.313,0.385 1.438,0.385 false 1.031,1.229 0.938,1.469 0.938,1.469 0.813,1.469 false 1.458,0.302 1.635,0.49 0.177,0.188 10 false *1 0.656,1.385 0.854,1.563 0.198,0.177 10 false *2 3.323,0.24 3.521,0.438 0.198,0.198 10 false *a

Text in Illustration
*1 Stopper *2 Nut
*a Push in - -


h.

Install the outer part of the transmission control cable to the shift lever retainer. Check that the spring is positioned at "A" and push in the stopper.

C200366E09
1.115,0.365 1.177,0.167 1.177,0.167 1.302,0.167 false 1.115,0.854 1.031,1.083 1.031,1.083 0.917,1.083 true 1.042,1.323 0.99,1.458 0.99,1.458 0.865,1.458 false 3.5,0.75 3.271,1.396 3.271,1.396 3.156,1.396 true 5.917,0.771 5.688,1.417 5.688,1.417 5.573,1.417 true 3.51,0.698 3.677,0.219 3.677,0.219 3.802,0.219 true 5.938,0.688 6.115,0.198 6.115,0.198 6.229,0.198 true 1.344,0.094 1.573,0.302 0.229,0.208 10 false *1 0.75,1 0.927,1.177 0.177,0.177 10 false *2 0.708,1.385 0.885,1.563 0.177,0.177 10 false *3 3.833,0.135 4.021,0.323 0.188,0.188 10 false *4 6.25,0.115 6.438,0.302 0.188,0.188 10 false *4 3.021,1.313 3.167,1.49 0.146,0.177 10 false A 5.448,1.333 5.594,1.51 0.146,0.177 10 false A

Text in Illustration
*1 Stopper *2 Nut
*3 Shift Lever Retainer *4 Spring

HINT:

If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.



i.
C264711E01
0.254,1.799 0.428,1.962 0.174,0.163 10 *1 0.448,1.888 1.414,1.636 false

Install the cable end to the shift lever assembly.

Text in Illustration
*1 Stopper

NOTICE:
·

Check that the lock piece is pulled up.

·

Install the cable end all the way to the base of the pin.




j.
C264712E02
1.094,1.542 0.5,1.542 true 1.563,1.604 2.292,1.208 2.292,1.208 2.542,1.208 true 0.333,1.458 0.563,1.646 0.229,0.188 10 false *2 2.563,1.115 2.792,1.302 0.229,0.188 10 false *1 1.969,1.594 2.198,1.781 0.229,0.188 10 false *a

Push the lock piece into the adjuster case.

Text in Illustration
*1 Lock Piece
*2 Adjuster Case
*a Push in

NOTICE:

Securely press in the lock piece until it locks.



k.

After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.


l.

Install the instrument cluster finish panel assembly and center instrument cluster finish panel sub- assembly (See page Drivetrain>K112 (CVT)>TRANSMISSION CONTROL CABLE>INSTALLATION).