53292A
1.REMOVE UPPER RADIATOR SUPPORT SEAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
16470
3.REMOVE RADIATOR RESERVOIR ASSEMBLY
16611
4.REMOVE RADIATOR RESERVOIR BRACKET
55712
5.REMOVE FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK
6.REMOVE BATTERY
17705
7.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17700
8.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
17751
9.REMOVE NO. 1 AIR CLEANER INLET
17752
10.REMOVE NO. 2 AIR CLEANER INLET
74411
11.REMOVE BATTERY CARRIER
74414D
12.REMOVE BATTERY CARRIER SUPPORT
45187
13.REMOVE NO. 3 STEERING WHEEL LOWER COVER
45186
14.REMOVE NO. 2 STEERING WHEEL LOWER COVER
45130
15.REMOVE STEERING PAD ASSEMBLY
45100
16.REMOVE STEERING WHEEL ASSEMBLY
45286
17.REMOVE STEERING COLUMN COVER
18.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE
55420A
19.REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY
55414A
20.REMOVE INSTRUMENT CLUSTER FINISH PANEL END (w/o Navigation System)
21.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
55650
22.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
55042B
23.REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
55660
24.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
55041B
25.REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY
67914B
26.REMOVE FRONT DOOR SCUFF PLATE LH
62112
27.REMOVE COWL SIDE TRIM BOARD LH
55607
28.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55550
29.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY
55474B
30.REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH
55447C
31.REMOVE NO. 1 SWITCH HOLE BASE
67913B
32.REMOVE FRONT DOOR SCUFF PLATE RH
62111C
33.REMOVE COWL SIDE TRIM BOARD RH
55606
34.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55432B
35.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/o Knee Airbag)
55432B
36.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/ Knee Airbag)
58534E
37.REMOVE FLOOR CARPET COVER CENTER LH
58533C
38.REMOVE FLOOR CARPET COVER CENTER RH
55434B
39.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER
40.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
Move the shift lever to N.
Disconnect the end of the transmission control cable from the shift lever assembly.
Using a screwdriver, pull out the stopper of the transmission control cable.
| *1 | Stopper |
Do not remove the stopper. If the stopper is removed, reinstall it to its original position.
Rotate the nut of the transmission control cable counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.
| *1 | Nut |
Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.
Remove the nut and disconnect the control cable assembly from the control shaft lever.
Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.
Disconnect the control cable assembly from the control cable bracket.
Remove the 2 nuts and disconnect the transmission control cable clamp from the body.
Remove the 2 bolts and disconnect the transmission control cable.
Pull out the transmission control cable.