Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START C

2GR-FE STARTING  PUSH-BUTTON START  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is output when a malfunction occurs in the ACCD output circuit, which is between the ACC relay actuation circuit inside the main body ECU and the ACC relay.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored. After the man body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2274 ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
·

Instrument panel junction block LH (Main body ECU)

·

Instrument panel junction block RH

·

Wire harness or connector



WIRING DIAGRAM

A135934E04
5.156,1.927 5.99,2.104 0.833,0.177 10 false ECU-ACC 0.948,3.01 1.469,3.302 0.521,0.292 10 false ACC 2.24,3.333 2.708,3.531 0.469,0.198 10 false ACCD 2.188,0.833 3.052,1.104 0.865,0.271 10 false from Battery 4.615,4.333 6.938,4.625 2.323,0.292 10 false Instrument Panel Junction Block RH 0.458,4.344 2.729,4.698 2.271,0.354 10 false Instrument Panel Junction Block LH (Main Body ECU) 5.542,3.677 5.938,3.906 0.396,0.229 10 false ACC 2.719,3.344 3.021,3.51 0.302,0.167 10 false G57 2.771,1.813 2.99,1.969 0.219,0.156 10 false 4A 2.781,3.125 3,3.271 0.219,0.146 10 false 22 2.792,1.583 2.979,1.74 0.188,0.156 10 false 26 4.406,1.802 4.615,1.99 0.208,0.188 10 false 5D 4.417,1.573 4.604,1.74 0.188,0.167 10 false 27 4.406,2.802 4.635,2.958 0.229,0.156 10 false 5M 4.406,3.354 4.615,3.563 0.208,0.208 10 false 5D 4.406,3.958 4.604,4.094 0.198,0.135 10 false 5A 4.448,3.771 4.563,3.917 0.115,0.146 10 false 4 4.448,3.135 4.573,3.281 0.125,0.146 10 false 3 4.448,2.583 4.583,2.74 0.135,0.156 10 false 1

PROCEDURE

1.READ VALUE USING GTS (ACC RELAY MONITOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / ACC Relay Mon.


d.

Read the display on the tester.

Main Body ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC Relay Monitor ACC relay monitor / ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
-

OK:

When the engine switch is turned on (ACC), ON is displayed on the tester.




OK

2.CHECK ENGINE SWITCH CONDITION

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
2.CHECK ENGINE SWITCH CONDITION
a.

Ensure the electrical key is inside the cabin.


b.

Check that the power source mode changes as shown below each time the engine switch is pushed.

OK:

off → on (ACC) → on (IG) → off


HINT:




OK

NORMAL

NG

GO TO OTHER PROBLEM

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.

Disconnect the G57 main body ECU connector.


b.

Disconnect the 5D instrument panel junction block RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
G57-22 (ACCD) - 5D-3 Below 1 Ω
G57-22 (ACCD) or 5D-3 - Body ground 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK RH - BODY GROUND)
a.

Disconnect the 5A instrument panel junction block RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
5A-4 - Body ground Below 1 Ω




OK

5.CHECK MAIN BODY ECU OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK MAIN BODY ECU OPERATION
a.

Reconnect the G57 instrument panel junction block RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
5D-3 - Body ground Engine switch on (ACC) 0.1 to 0.8 V (*1) → Output voltage at terminal AM1 or AM2 is -2 V or more.


HINT:
·

*1: Voltage is output only when the engine is cranking.

·

Terminal AM1: G57-6

·

Terminal AM2: G58-1





OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH