Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › 2013.04–2014.09
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292105 AUTOMATIC TRANSAXLE ASSEMBLY A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32000 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C206959

Engage the splines of the input shaft and turbine runner.


b.
C206960

Engage the splines of stator shaft and the stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter assembly back approximately 10 mm and engage the splines while rotating the torque converter assembly.



c.
C206961

Turn the torque converter assembly to engage the key of the oil pump drive gear into the slot on the torque converter assembly.


d.
C202919E08
0.333,0.292 0.438,0.292 0.438,0.292 0.625,0.74 false 1.375,2.323 1.375,3.052 false 2.625,1.229 2.625,1.49 false 2.823,1.75 2.656,1.917 2.656,1.917 2.656,2.021 false 0.156,0.219 0.354,0.385 0.198,0.167 10 false *1 2.552,1.51 2.75,1.677 0.198,0.167 10 false *1 2.417,0.719 2.552,0.885 0.135,0.167 10 false A 2.594,2.042 2.76,2.208 0.167,0.167 10 false *2 1.313,3.073 1.479,3.24 0.167,0.167 10 false *2

Using a vernier caliper and a straightedge, measure dimension "A" between the transaxle contact surfaces of the engine *1 and the torque converter assembly contact surfaces of the drive plate *2. (#)

NOTICE:

Make sure to deduct the thickness of the straightedge.



e.
C206962E02
2.75,0.208 2.875,0.375 0.125,0.167 10 false B

Using a vernier caliper and a straightedge, measure dimension "B" shown in the illustration and check that "B" is greater than "A" which was measured in step (#).

Standard:

A + 1.0 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transaxle is installed to the engine with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.




Hide 33823 3.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C140268

Install the cable bracket with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 35013 4.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.
C140267

Install the filler tube with the bolt.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Install the ATF dipstick.


Hide 30500 5.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C206963E02
1.615,0.885 1.74,0.781 1.74,0.781 2.021,0.781 true 1.188,0.979 0.979,0.979 false 0.292,0.896 1.042,1.073 0.75,0.177 10 false Crankshaft 2.063,0.708 3.135,1.344 1.073,0.635 10 true Torque Converter Centerpiece

Apply clutch spline grease to the contact surface between the crankshaft and torque converter assembly centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum spread:

About 1 g (0.353 oz)



b.
C193868E05
0.823,2.292 0.948,2.438 0.125,0.146 10 false A 1.896,2.281 2.021,2.448 0.125,0.167 10 false A 0.354,3.01 0.479,3.177 0.125,0.167 10 false A 0.25,3.615 0.375,3.781 0.125,0.167 10 false B 2.417,2.75 2.542,2.917 0.125,0.167 10 false B

Install the automatic transaxle to the engine with the 5 upper side mounting bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

for bolt A

46 N*m (469 kgf*cm, 34 ft.*lbf)

for bolt B


NOTICE:

Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.



c.
C127820

Install the 4 lower side mounting bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


d.
A004869E08
2.156,0.906 2.365,1.354 false 2.125,1.365 2.75,1.563 0.625,0.198 10 false Adhesive

Apply adhesive to the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or Equivalent



e.
C129381

Install the 6 torque converter assembly mounting bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

HINT:

First install the black colored bolt and then the 5 bolts.



f.

Install the flywheel housing under cover.


Hide 12325A 6.INSTALL ENGINE MOUNTING BRACKET LH

a.
C138675

Install the mounting bracket LH with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12311A 7.INSTALL FRONT ENGINE MOUNTING BRACKET

a.
C138674

Install the mounting bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12321A 8.INSTALL REAR ENGINE MOUNTING BRACKET

a.
C138673

Install the mounting bracket with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 10.CONNECT WIRE HARNESS

a.
C138672

Connect the wire harness clamps.


b.

Connect the speed sensor connectors.


c.

Connect the transaxle wire connector.


d.

Connect the park/neutral position switch connector.


Hide 28100 11.INSTALL STARTER ASSEMBLY

a.
A133101

Install the starter with the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


b.
A133097

Connect the starter connector.


c.

Install the terminal nut and cover the nut with the cap.

Torque:
9.8 N*m (100 kgf*cm, 7 ft.*lbf)


Hide 12.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Install the engine assembly with transaxle (See page Engine / Hybrid System>2AZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION).


Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 14.ADD AUTOMATIC TRANSAXLE FLUID

Fluid type:

Toyota Genuine ATF WS


Hide 15.INSPECT AUTOMATIC TRANSAXLE FLUID

Hide 16.PERFORM RESET MEMORY

a.

Perform the RESET MEMORY procedures (A/T initialization) (See page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).