Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › SHIFT LEVER(for LHD) › from 2016.05
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292109 SHIFT LEVER(for LHD) A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER(for LHD)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL SHIFT LEVER ASSEMBLY

C133013

a.

Install the floor shift with the 4 bolts and screw.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

for 12 mm bolt



b.

Connect the 2 connectors.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C133005E06
2.25,1.802 2.375,2.042 false 1.438,0.99 1.135,0.875 false 2.375,0.875 2.719,1.073 0.344,0.198 10 false Turn 2.344,2.052 2.646,2.281 0.302,0.229 10 false Nut 0.635,0.76 1.167,0.948 0.531,0.188 10 false Stopper 1.875,0.146 2.281,0.385 0.406,0.24 10 false Push

a.

Rotate the transmission control cable nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper until it makes 2 "click" sounds.


b.
U189032E02
1.76,0.646 2.198,0.646 false 2.271,0.552 2.438,0.75 0.167,0.198 10 false A

Install the cable outer of the transmission control cable to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and press in the stopper.

HINT:

If the stopper cannot be pressed in, slightly rotate the nut clockwise and then press in the stopper.



c.
C133008

Connect the control cable to the shift lever.

NOTICE:

Make sure the cable is installed to the base of the pin.



Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 55900A 6.INSTALL HEATER CONTROL AND ACCESSORY

Hide 55434B 7.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER

Hide 55432B 8.INSTALL INSTRUMENT PANEL FINISH PANEL LOWER

Hide 58533C 9.INSTALL FLOOR CARPET COVER CENTER LH

Hide 58534E 10.INSTALL FLOOR CARPET COVER CENTER RH

Hide 55606 11.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 12.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55474B 14.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 55041B 15.INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55660 16.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

Hide 55042B 17.INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY

Hide 55650 18.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

Hide 55414A 19.INSTALL INSTRUMENT CLUSTER FINISH PANEL END

Hide 55420A 20.INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER ASSEMBLY

Hide 33504F 21.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 22.PERFORM INITIALIZATION

a.

Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.