Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2013.04–2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292111 AUTOMATIC TRANSAXLE SYSTEM C

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the TCM.

If the TCM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The TCM then illuminates the MIL and sets the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. DTC Detection Condition Trouble Area
P0617 When conditions (a), (b) and (c) are met, positive (+B) battery voltage 10.5 V or more is applied to the TCM for 20 seconds.
(1-trip detection logic):
(a) Vehicle speed more than 20 km/h (12.4 mph)
(b) Engine speed more than 1,000 rpm
(c) STA signal ON
·

Park/neutral position switch

·

Starter relay circuit

·

Ignition switch

·

TCM



WIRING DIAGRAM

C157359E03
6.344,0.073 6.667,0.25 0.323,0.177 10 false ECM 6.375,2.677 6.698,2.854 0.323,0.177 10 false TCM 1.615,2.021 2.177,2.198 0.563,0.177 10 false ST 0.323,2.719 1.021,2.896 0.698,0.177 10 false FL MAIN 0.74,4.49 1.365,4.667 0.625,0.177 10 false Battery 4.667,2.958 4.833,3.125 0.167,0.167 10 false P 1.604,2.5 2.167,2.677 0.563,0.177 10 false Starter 4.854,2.958 5.021,3.125 0.167,0.167 10 false N 4.458,3.135 4.625,3.302 0.167,0.167 10 false B 4.469,3.344 4.635,3.51 0.167,0.167 10 false L 4.26,2.24 4.563,2.396 0.302,0.156 10 false D4 4.26,2.406 5.177,2.583 0.917,0.177 10 false Park/Neutral 4.25,2.573 5.615,2.74 1.365,0.167 10 false Position Switch 4.271,1.51 4.573,1.667 0.302,0.156 10 false To 4.271,1.677 5.188,1.854 0.917,0.177 10 false Main Body 4.271,1.844 4.917,2.01 0.646,0.167 10 false ECU 5.875,1.198 6.083,1.354 0.208,0.156 10 false 48 5.875,1.385 6.094,1.563 0.219,0.177 10 false A7 5.875,1.667 6.083,1.823 0.208,0.156 10 false 62 5.875,1.844 6.135,2.021 0.26,0.177 10 false D1 5.875,2.99 6.083,3.146 0.208,0.156 10 false 11 5.875,3.167 6.125,3.344 0.25,0.177 10 false D5 5.885,3.792 6.094,3.948 0.208,0.156 10 false 10 5.885,3.979 6.156,4.156 0.271,0.177 10 false D5 5.938,4.271 6.146,4.427 0.208,0.156 10 false 8 5.885,4.469 6.125,4.646 0.24,0.177 10 false D5 6.198,3.146 6.656,3.323 0.458,0.177 10 false NSW 6.198,3.969 6.656,4.146 0.458,0.177 10 false STA 6.208,4.458 6.667,4.635 0.458,0.177 10 false E1 6.167,1.854 6.625,2.031 0.458,0.177 10 false NSW 6.177,1.385 6.635,1.563 0.458,0.177 10 false STA 2.719,2.729 2.927,2.885 0.208,0.156 10 false 1 2.677,2.917 3.01,3.094 0.333,0.177 10 false D6 0.771,3.167 0.979,3.323 0.208,0.156 10 false 1 0.74,3.344 1.073,3.521 0.333,0.177 10 false E1 3.521,3.594 3.771,3.75 0.25,0.156 10 false ST 3.292,3.01 3.5,3.167 0.208,0.156 10 false 3 3.844,3.448 4.052,3.604 0.208,0.156 10 false 1 3.292,3.448 3.5,3.604 0.208,0.156 10 false 2 3.833,3.01 4.042,3.167 0.208,0.156 10 false 5 4.271,3.26 4.479,3.417 0.208,0.156 10 false 9 5.042,3.073 5.25,3.229 0.208,0.156 10 false 4 0.531,2.031 1.375,2.208 0.844,0.177 10 false F/B BATT

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally. If the engine does not crank, proceed to the problem symptoms table (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. The TCM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / ECT / Data List.


d.

Check the value displayed on the tester when the ignition switch is turned on (IG) and the engine is started.

OK:
Tester Display Measurement Item/Range Normal Condition
Starter Signal Starter signal/ ON or OFF ON: Cranking




NG

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

OK

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
U188261E02
1.219,1.552 0.656,1.271 false 1.292,1.969 0.667,2.292 false 0.063,0.094 1.271,0.281 1.208,0.188 10 false Component Side: 0.656,2.563 2.531,2.729 1.875,0.167 10 false Park/Neutral Position Switch 0.406,1.646 0.625,1.833 0.219,0.188 10 false D4 0.458,1.146 0.635,1.333 0.177,0.188 10 false B 0.51,2.208 0.688,2.396 0.177,0.188 10 false L

Inspect the park/neutral position switch.

i.

Disconnect the park/neutral position switch connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Gear Selector Lever Position Specified Condition
B (D4-4) - L(D4-9) P Below 1 Ω
B (D4-4) - L(D4-9) N Below 1 Ω



iii.

Reconnect the park/neutral position switch connector.




OK

NG