Home › Drivetrain › U660E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY › from 2016.05
RM24M0E _52 Drivetrain _059579 U660E AUTOMATIC TRANSMISSION / TRANSAXLE _0292121 AUTOMATIC TRANSAXLE ASSEMBLY A

U660E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When the automatic transaxle is replaced, the transaxle's compensation code must be input into the TCM (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION).

·

When the TCM is replaced, the existing transaxle compensation codes must be input into a new TCM (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION).

·

If the following parts have been replaced, initialize the TCM and perform a road test to allow the TCM to learn (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).

-

Valve body assembly

-

Shift solenoid SL3

-

Shift solenoid SL4


·

If the following parts have been replaced, perform a road test to allow the TCM to learn (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).

-

Shift solenoid SL1

-

Shift solenoid SL2


·

If the TCM or transaxle has been replaced, register the transmission compensation code in the TCM (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>REGISTRATION).

·

Perform RESET MEMORY (AT initialization) when replacing the automatic transaxle assembly, engine assembly or ECM (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>INITIALIZATION).



PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Remove the engine assembly with transaxle (see page Engine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL).


Hide 11361J 3.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C139871

Remove the 2 bolts and flywheel housing under cover.


Hide 30500 4.REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

a.
U189404

Slide the clip and disconnect the breather plug hose from the transmission breather skirt.


b.

Remove the bolt and transmission breather skirt from the engine cylinder head.


c.
A205885

Remove the 6 torque converter assembly set bolts.


d.
C135007

Remove the 11 bolts and transaxle.

NOTICE:

To prevent damage to the knock pin, do not pry between the transaxle and engine.



Hide 5.SEPARATE WIRE HARNESS

a.
C139612

Remove the 2 bolts and separate the 2 wire harnesses from the transaxle.


Hide 6.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C161404

Remove the 2 bolts and 2 wire harness clamp brackets from the transaxle.


Hide 7.REMOVE OIL COOLER HOSE

a.

w/o Air Cooled Oil Cooler

i.
C202159

Slide the 2 clips and remove the 2 oil cooler hoses from the transaxle.



b.

w/ Air Cooled Oil Cooler

i.
C204422

Slide the 2 clips and remove the 2 oil cooler hoses from the transaxle.



Hide 12325A 8.REMOVE ENGINE MOUNTING BRACKET LH

a.
C367640

Remove the 4 bolts and engine mounting bracket LH from the automatic transaxle assembly.


Hide 89530C 9.REMOVE TCM

a.
C133604

Release the lock lever and disconnect the connector from the TCM.


b.
U189415

Remove the 2 bolts and TCM from the automatic transaxle assembly.


Hide 33823 10.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C139615

Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.


Hide 33403M 11.REMOVE SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY

a.
C135002

Remove the bolt and speedometer driven hole (ATM) cover sub-assembly from the automatic transaxle assembly.


Hide 32000 12.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C157087

Remove the torque converter assembly from the automatic transaxle assembly.