Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.04–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0273/13  Open in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies the power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay ON and operates the ABS pump motor.

DTC No. DTC Detection Condition Trouble Area
C0273/13 When either condition below is met:
1.

Pump motor voltage is 2.0 V or more for 1 sec. or more at motor relay OFF.

2.

Pump motor voltage is (IG - 4.0 V) or less for 0.1 sec. or more at motor relay ON.

3.

After the end of the actuation of the motor relay slow down condition of motor does not meet the specification.


·

ABS NO. 1 H-fuse

·

Wire harness (+BM circuit)

·

Brake actuator



HINT:

C0273/13: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 15 km/h (9 mph).


WIRING DIAGRAM

Refer to DTC C0226/21, C0236/22, C0246/23, C0256/24 (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C0226/21).

PROCEDURE

1.INSPECT FUSE (ABS NO. 1)
a.

Remove the ABS NO. 1 H-fuse from the engine room No. 1 relay block.


b.

Measure the resistance of the fuse.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U189307E02
1.354,1.813 1.875,2.635 false 0.823,1.813 0.479,2.625 false 1.031,1.823 1.146,2.75 false 0.135,0.094 1.75,0.292 1.615,0.198 10 false Wire Harness Side: 1.5,0.729 1.844,0.885 0.344,0.156 10 false A22 1.052,2.813 1.375,2.99 0.323,0.177 10 false +BM 0.24,2.667 0.76,2.844 0.521,0.177 10 false GND2 1.802,2.677 2.323,2.854 0.521,0.177 10 false GND1

Disconnect the A22 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
A22-2 (+BM) - Body ground 10 to 14 V



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A22-4 (GND1) - Body ground Below 1 Ω
A22-1 (GND2) - Body ground Below 1 Ω




OK

3.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (MOTOR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM ACTIVE TEST BY INTELLIGENT TESTER (MOTOR RELAY)
a.

Select the Active Test, generate a control command, and then check that the motor relay operates.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON/OFF Operation sound of motor can be heard

OK:

Operation sound of the ABS motor is heard.




OK

4.RECONFIRM DTC

NG

4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at 15 km/h (9 mph) or more to activate the initial check.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B