Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.04–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

If any of the following conditions are detected, the ABS warning light remains on:

1.

The ECU connectors are disconnected from the skid control ECU.

2.

There is a malfunction in the skid control ECU internal circuit.

3.

There is an open or short in the wire harness between the combination meter and the skid control ECU.


HINT:

The intelligent tester may not be used when there is a malfunction in the skid control ECU.


WIRING DIAGRAM

C139058E10
0.594,7.208 1.844,7.385 1.25,0.177 10 false Combination Meter 5.667,2.781 5.979,2.948 0.313,0.167 10 false A22 5.688,1 6.198,1.167 0.51,0.167 10 false CANH 5.698,1.26 6.198,1.458 0.5,0.198 10 false CANL 4.656,5.719 5.76,5.948 1.104,0.229 10 false Main Body ECU 0.969,1.115 1.542,1.292 0.573,0.177 10 false CAN I/F 0.771,2.365 1.76,2.573 0.99,0.208 10 false CAN Controller 1.042,2.885 1.448,3.083 0.406,0.198 10 false CPU 0.875,4.198 1.677,4.396 0.802,0.198 10 false LED Driver 0.75,6.25 1.156,6.438 0.406,0.188 10 false ABS 5.688,1.646 6.177,1.854 0.49,0.208 10 false GND1 5.677,2.01 6.156,2.208 0.479,0.198 10 false GND2 5.698,2.385 5.979,2.531 0.281,0.146 10 false IG1 3.979,2.563 4.948,2.719 0.969,0.156 10 false GAUGE NO. 1 3.448,4.604 4.396,4.781 0.948,0.177 10 false LH-IG Relay 2 3.719,6.813 4.073,7.01 0.354,0.198 10 false IG2 2.771,7.688 3.385,7.875 0.615,0.188 10 false FL MAIN 2.177,8.083 2.792,8.271 0.615,0.188 10 false Battery 2.729,6.615 3.083,6.802 0.354,0.188 10 false MET 5.896,3.771 6.26,3.948 0.365,0.177 10 false ALT 5.094,6.604 5.375,6.781 0.281,0.177 10 false IG2 5.302,4.615 5.646,4.823 0.344,0.208 10 false AM1 4.698,5.313 5.052,5.51 0.354,0.198 10 false IG2D 5.313,5.333 5.656,5.542 0.344,0.208 10 false AM2 6.094,5.177 6.802,5.354 0.708,0.177 10 false AM2 NO. 2 4.708,4.302 5.063,4.5 0.354,0.198 10 false IG1D 1.885,1.146 2.396,1.313 0.51,0.167 10 false CANH 1.906,1.417 2.406,1.615 0.5,0.198 10 false CANL 2.021,6.573 2.292,6.76 0.271,0.188 10 false IG2 2.365,6.302 2.594,6.51 0.229,0.208 10 false 21 3.438,6.333 3.604,6.542 0.167,0.208 10 false 3 4.458,4.094 4.625,4.302 0.167,0.208 10 false 3 4.438,5.094 4.625,5.302 0.188,0.208 10 false 11 4.208,6.333 4.375,6.542 0.167,0.208 10 false 5 4.208,5.198 4.375,5.406 0.167,0.208 10 false 1 5.75,5.115 5.917,5.271 0.167,0.156 10 false 1 5.51,1.917 5.677,2.125 0.167,0.208 10 false 1 5.76,4.417 5.927,4.583 0.167,0.167 10 false 6 3.438,5.198 3.604,5.406 0.167,0.208 10 false 2 5.375,7.688 6,7.833 0.625,0.146 10 false F/B BATT 5.667,4.615 5.99,4.781 0.323,0.167 10 false G57 5.667,5.313 5.99,5.479 0.323,0.167 10 false G58 4.375,5.323 4.698,5.49 0.323,0.167 10 false G58 4.365,4.292 4.688,4.458 0.323,0.167 10 false G57 4.552,3.771 5.406,3.958 0.854,0.188 10 false LH-MAIN-JB 2.375,1.188 2.563,1.344 0.188,0.156 10 false 31 2.375,0.906 2.563,1.063 0.188,0.156 10 false 32 5.427,0.896 5.615,1.083 0.188,0.188 10 false 26 5.427,1.177 5.667,1.365 0.24,0.188 10 false 15 5.427,2.313 5.667,2.5 0.24,0.188 10 false 18 5.479,1.531 5.667,1.719 0.188,0.188 10 false 4 5.667,2.938 6.885,3.125 1.219,0.188 10 false Skid Control ECU 0.594,7.052 0.958,7.229 0.365,0.177 10 false G28

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if the CAN communication system DTC is output (see page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT SKID CONTROL ECU CONNECTOR

B

2.INSPECT SKID CONTROL ECU CONNECTOR
a.

Check if the skid control ECU connector is properly installed.

OK:

The skid control ECU connector is properly installed.




OK

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR TO ECU SECURELY

3.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U189310E02
1.354,1.813 1.656,2.625 false 1.844,1.865 2.313,2.646 false 0.823,1.823 0.833,2.635 false 0.104,0.094 1.531,0.292 1.427,0.198 10 false Wire Harness Side: 1.5,0.74 1.823,0.896 0.323,0.156 10 false A22 0.729,2.656 1.25,2.833 0.521,0.177 10 false GND2 1.552,2.656 2.073,2.833 0.521,0.177 10 false GND1 2.271,2.667 2.542,2.844 0.271,0.177 10 false IG1

Disconnect the A22 ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A22-4 (GND1) - Body ground Below 1 Ω
A22-1 (GND2) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
A22-18 (IG1) - Body ground Engine switch on (IG) 10 to 14 V




OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS WARNING LIGHT)
a.

Select the Active Test, generate a control command, and then check that the ABS warning light operates.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe combination meter

OK:

The ABS warning light is turned on or off.



HINT:

When the ABS warning light remains illuminated, opens in the wire harness of the combination meter or abnormalities in the meter circuit should be considered.



OK

NG