Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2014.09–2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292157 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0200/31  Right Front Wheel Speed Sensor Signal  C0205/32  Left Front Wheel Speed Sensor Signal  C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1330/35  Right Front Speed Sensor Circuit  C1331/36  Left Front Speed Sensor Circuit  


DESCRIPTION

The speed sensors detect the wheel speeds and send appropriate signals to the skid control ECU.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change as the rotors turn.

The speed sensors detect those magnetic changes and send pulse signals to the skid control ECU. The ECU monitors the wheel speeds through these pulse signals to control the ABS control system.

DTCs C1271/71, C1272/72, C1275/75 and C1276/76 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs C1271/71, C1272/72, C1275/75/75 and C1276/76 are output only in the test mode.

C115116E28
2.042,0.833 2.354,0.688 false 2.573,1.677 2.938,1.365 false 5.292,0.781 5.521,0.333 false 6.125,1.104 5.875,1.292 false 0.167,0.125 1.771,0.354 1.604,0.229 10 false Front Speed Sensor: 3.625,0.156 5.073,0.354 1.448,0.198 10 false Rear Speed Sensor: 2.385,0.594 3.365,0.813 0.979,0.219 10 false Speed Sensor 5.531,0.188 6.51,0.406 0.979,0.219 10 false Speed Sensor 6.156,1.01 7.073,1.229 0.917,0.219 10 false Sensor Rotor 2.969,1.24 3.885,1.458 0.917,0.219 10 false Sensor Rotor 2.896,3.406 3.771,3.625 0.875,0.219 10 false Low Speed 3.823,3.458 4.698,3.677 0.875,0.219 10 false High Speed 4.885,2.688 5.458,2.896 0.573,0.208 10 false 14 mA 4.938,3.031 5.51,3.24 0.573,0.208 10 false 7 mA

DTC No. DTC Detection Condition Trouble Area
C0200/31
C0205/32
When one of following conditions is met:
1.

Non-plausible high frequent signal, high wheel acceleration or high gradient for 20 sec. with the brake pedal applied or for 5 sec. when the brake pedal is not applied.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), the wheel speed of 0 km/h (0 mph) is detected.

3.

Deviation of 2 wheel speed.


·

Front speed sensor

·

Front speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1271/71
C1272/72
Detected only during test mode.
·

Front speed sensor

·

Front speed sensor circuit

·

Sensor installation

·

Foreign matter on sensor rotor


C1275/75
C1276/76
Detected only during test mode.
·

Front speed sensor

·

Front speed sensor circuit

·

Sensor installation


C1330/35
C1331/36
Abnormality in the resistance value of each speed sensor is detected.
·

Front speed sensor RH and/or LH

·

Front speed sensor circuit RH and/or LH

·

Sensor installation

·

Brake actuator (Skid control ECU)



HINT:
·

DTCs C0200/31 and C1330/35 relate to the front speed sensor RH.

·

DTCs C0205/32 and C1331/36 relate to the front speed sensor LH.



WIRING DIAGRAM

C143427E08
5.698,3.188 6.896,3.573 1.198,0.385 10 false Skid Control ECU 0.76,0.854 2.375,1.219 1.615,0.365 10 false Front Speed Sensor LH 0.75,2.219 2.323,2.583 1.573,0.365 10 false Front Speed Sensor RH 2.302,0.552 2.458,0.708 0.156,0.156 10 false 2 2.302,1.167 2.448,1.354 0.146,0.188 10 false 1 2.302,1.865 2.458,2.021 0.156,0.156 10 false 2 2.313,2.5 2.458,2.688 0.146,0.188 10 false 1 5.875,0.469 6.188,0.656 0.313,0.188 10 false FL+ 5.865,1.229 6.177,1.417 0.313,0.188 10 false FL- 5.865,1.781 6.177,1.969 0.313,0.188 10 false FR+ 5.865,2.542 6.177,2.729 0.313,0.188 10 false FR- 5.563,0.375 5.781,0.542 0.219,0.167 10 false 16 5.625,1.115 5.844,1.281 0.219,0.167 10 false 5 5.635,1.667 5.854,1.833 0.219,0.167 10 false 9 5.573,2.427 5.792,2.594 0.219,0.167 10 false 10 0.76,0.688 1.073,0.885 0.313,0.198 10 false A5 0.75,2.042 1.208,2.24 0.458,0.198 10 false A20 5.698,3 6.156,3.198 0.458,0.198 10 false A22

CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal in test mode after cleaning or replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.READ VALUE USING DATA LIST (MOMENTARY INTERRUPTION)
a.

Using the Data List of the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Speed Open FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-
FL Speed Open FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
NORMAL: Normal
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING DATA LIST (FRONT SPEED SENSOR)

NG

CHECK AND REPAIR HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)

2.READ VALUE USING DATA LIST (FRONT SPEED SENSOR)
a.

Check the Data List for proper functioning of the front speed sensor.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Wheel speed sensor (FR) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer
FL Wheel Speed Wheel speed sensor (FL) reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer

OK:

There is almost no difference between actual wheel speed and displayed speed value.


HINT:

There is a tolerance of +-10% in the speedometer indication.




OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.INSPECT FRONT SPEED SENSOR (INSTALLATION)
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform a test mode inspection and check for DTCs (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).

OK:

No DTC output.




OK

4.RECONFIRM DTC

NG

CHECK AND REPAIR HARNESS OR CONNECTOR (SPEED SENSOR CIRCUIT)

4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B

9.REPLACE FRONT SPEED SENSOR
5.INSPECT FRONT SPEED SENSOR (INSTALLATION)
a.
C108871E03
0.614,1.66 1.511,1.826 0.897,0.165 10 No Clearance 0.71,1.348 0.862,1.66 false 1.117,0.134 1.992,0.336 0.875,0.203 10 8.5 N*m 0.125,1.695 0.411,1.849 0.286,0.154 10 OK 2.947,1.481 3.234,1.635 0.286,0.154 10 NG 0.83,0.475 0.951,0.199 0.951,0.199 1.08,0.199 false

Check that the speed sensor installation bolt is tightened properly.

OK:

The installation bolt is tightened properly, and there is no clearance between the sensor and front steering knuckle.


Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



HINT:

If the installation portion of the sensor is dirty, clean it and reinstall the sensor.

Check the speed sensor after the speed sensor replacement (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).



OK

6.CHECK SPEED SENSOR (TIP)

NG

TIGHTEN BOLT PROPERLY OR REPLACE FRONT SPEED SENSOR

6.CHECK SPEED SENSOR (TIP)
a.

Remove the front speed sensor.


b.

Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


HINT:

Check the speed sensor signal after cleaning or replacing the speed sensor (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).




OK

7.CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.CHECK WIRE HARNESS (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.
U189318E02
1.948,1.604 2.573,0.885 false 2.083,1.594 2.917,1.073 false 1.563,1.625 1.375,2.313 false 1.615,1.74 1.708,2.323 false 0.125,0.052 1.708,0.25 1.583,0.198 10 false Wire Harness Side: 1.167,0.521 2.333,0.708 1.167,0.188 10 false Skid Control ECU 0.188,0.75 0.479,0.917 0.292,0.167 10 false A22 0.229,3.219 0.573,3.438 0.344,0.219 10 false A5 1.771,3.229 2.115,3.448 0.344,0.219 10 false A20 1.094,2.677 2.448,2.906 1.354,0.229 10 false Front Speed Sensor 1.25,2.344 1.521,2.531 0.271,0.188 10 false FL- 1.688,2.354 1.958,2.542 0.271,0.188 10 false FL+ 2.594,0.802 2.896,0.958 0.302,0.156 10 false FR+ 2.969,0.958 3.24,1.115 0.271,0.156 10 false FR-

Disconnect the A22 ECU connector.


b.

Disconnect the A5 and A20 sensor connectors.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
for LH:
Tester Connection Specified Condition
A22-16 (FL+) - A5-2 Below 1 Ω
A22-5 (FL-) - A5-1 Below 1 Ω
A22-16 (FL+) - Body ground 10 kΩ or higher
A22-5 (FL-) - Body ground 10 kΩ or higher

for RH:
Tester Connection Specified Condition
A22-9 (FR+) - A20-2 Below 1 Ω
A22-10 (FR-) - A20-1 Below 1 Ω
A22-9 (FR+) - Body ground 10 kΩ or higher
A22-10 (FR-) - Body ground 10 kΩ or higher




OK

8.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

9.REPLACE FRONT SPEED SENSOR

B

END

9.REPLACE FRONT SPEED SENSOR
a.


NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.


d.

Check if the same DTC(s) is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

END

B