Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2013.04–2014.09
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0278/11  Open in ABS Solenoid Relay Circuit  


DESCRIPTION

The solenoid relay supplies power to the ABS solenoid and TRC solenoid.

After the engine switch is turned on (IG), the vehicle speed has reached 15 km/h (9 mph) and the solenoid is determined to be normal by the initial check self-diagnosis, the relay switches on. If any open or short circuits are detected, the relay switches off.

These DTCs may be set if the voltage supply to the solenoid relay (+BS) falls below the DTC detection threshold due to the battery or alternator outputs being insufficient.

DTC No. DTC Detection Condition Trouble Area
C0278/11 When either condition below is met:
1.

3 or more solenoid valves are determined to be fault and voltage supplied to the solenoid to be fault at the same time.

2.

Solenoid valve relay is not turned OFF.


·

ABS NO. 1 H-fuse

·

Wire harness (+BS circuit)

·

ABS and TRACTION actuator



HINT:

DTCs C0278/11: The skid control ECU begins to detect these DTCs when the vehicle speed exceeds 15 km/h (9 mph).


PROCEDURE

1.INSPECT FUSE (ABS NO. 2)
a.

Remove the ABS NO. 2 H-fuse from the engine room No. 1 relay block.


b.

Measure the resistance of the H-fuse.

Standard resistance:

Below 1 Ω




OK

2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPLACE FUSE

2.CHECK WIRE HARNESS (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U189326E02
0.906,1.781 0.979,2.281 false 0.74,1.771 0.51,2.281 false 1.198,1.771 1.49,2.281 false 0.135,0.25 1.427,0.396 1.292,0.146 10 false Wire Harness Side: 0.469,0.875 0.667,1.021 0.198,0.146 10 false A9 0.865,2.292 1.188,2.458 0.323,0.167 10 false +BM 0.25,2.292 0.75,2.458 0.5,0.167 10 false GND2 1.354,2.292 1.854,2.458 0.5,0.167 10 false GND1

Disconnect the A9 ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
A9-2 (+BM) - Body ground 10 to 14 V



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A9-4 (GND1) - Body ground Below 1 Ω
A9-1 (GND2) - Body ground Below 1 Ω




OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at 15 km/h (9 mph) or more to activate the initial check.


d.

Check if the same DTC is output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output (for 2AZ-FE) A
DTC is output (for 2GR-FE) B
DTC is not output C



A

B

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY

C

END