Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1436  Yaw Rate Sensor Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) detects improper installation of the yaw rate and acceleration sensor or an abnormality in the difference between the yaw rate sensor value and the control value estimated based on the acceleration sensor, steering angle sensor and speed sensor signals.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1436 Yaw Rate Sensor Malfunction Difference between the yaw rate sensor value and the control value estimated inside the skid control ECU (brake actuator assembly) is abnormal.
·

Sensor installation

·

Yaw rate sensor (yaw rate and acceleration sensor)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate and acceleration sensor, perform acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Yaw Rate Sensor Yaw rate sensor / Min.: -128 °/s, Max.: 127 °/s Vehicle stopped: 0 °/s
Turning right: -128 to 0 °/s
Turning left: 0 to 127 °/s
-


d.

Check the yaw rate and acceleration sensor output value displayed on the GTS.

Result:
Result Proceed to
NG (The yaw rate and acceleration sensor output value is 0 °/s when the vehicle is stationary, but the value fluctuates when turning.) A
NG (The yaw rate and acceleration sensor output value is not 0 °/s when the vehicle is stationary.) B
OK C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION

B

C

2.CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION
a.

Turn the engine switch off.


b.

Drive the vehicle straight ahead at 50 km/h (31 mph) or more for at least 30 seconds.


c.

Check that the steering wheel is correctly centered while driving straight ahead.

HINT:

If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.


OK:

The steering wheel is correctly centered.




OK

3.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING

3.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Check that the yaw rate and acceleration sensor has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR>INSTALLATION).

OK:

The yaw rate and acceleration sensor is tightened to the specified torque.

The yaw rate and acceleration sensor is not installed in a tilted position.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY