Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.05
RM24M0E _54 Brake _059583 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0292158 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1234  Yaw Rate Sensor  C1472  Acceleration Sensor  C1474  Forward and Rearward G Sensor  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor and the CAN communication system, DTC U0123 (Lost Communication with Yaw Rate Sensor Module) is output. When U0123 is output together with C1234, C1472 and/or C1474, inspect and repair the trouble areas indicated by U0123 first.


These DTCs may be stored if one of the following occurs:

·

Yaw rate and acceleration sensor circuit malfunction.

·

Yaw rate and acceleration sensor installation abnormality.

·

Yaw rate and acceleration sensor signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1234 Yaw Rate Sensor Any of the following is detected:
1.

The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off.

2.

The offset correction did not complete with the vehicle stopped, and the yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven.

3.

The offset correction completed with the vehicle stopped and the yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s.

4.

The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed while the vehicle is being driven.

5.

After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 5 seconds or more when the vehicle is stopped.

6.

After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more when the vehicle starts off.

7.

After the VSC system has started, but before the vehicle has started off, as the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more.

8.

The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s for 0.8 seconds or more.

9.

The change of the yaw rate sensor value within 0.04 seconds is abnormal.

10.

The value from the yaw rate sensor is judged as abnormal based on the skid control ECU (brake actuator assembly) estimation.


·

Sensor installation

·

Yaw rate sensor (yaw rate and acceleration sensor)

·

Yaw rate sensor circuit


C1472 Acceleration Sensor Any of the following is detected:
1.

With the vehicle stopped, the internal acceleration value is less than -7 m/s2 or more than 7 m/s2 for 0.4 seconds or more.

2.

The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.

3.

The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 0.8 seconds or more.


·

Sensor installation

·

Acceleration sensor (yaw rate and acceleration sensor)

·

Acceleration sensor circuit


C1474 Forward and Rearward G Sensor Any of the following is detected:
1.

The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.

2.

The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 3 seconds or more.


·

Sensor installation

·

Acceleration sensor (yaw rate and acceleration sensor)

·

Acceleration sensor circuit



WIRING DIAGRAM

C311976E03
5.313,4.115 6.979,4.521 1.667,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.323,3.927 5.635,4.135 0.313,0.208 10 false A35 6.042,0.75 6.521,0.958 0.479,0.208 10 false CANL 6.042,1.365 6.688,1.573 0.646,0.208 10 false CANH 5.771,0.563 6.031,0.771 0.26,0.208 10 false 14 5.771,1.177 6.031,1.323 0.26,0.146 10 false 26 1.281,0.573 1.531,0.781 0.25,0.208 10 false 3 1.281,1.188 1.542,1.396 0.26,0.208 10 false 2 1.281,1.875 1.51,2.083 0.229,0.208 10 false 1 1.292,2.479 1.615,2.688 0.323,0.208 10 false 4 0.813,0.76 1.24,0.969 0.427,0.208 10 false CANL 0.792,1.365 1.292,1.573 0.5,0.208 10 false CANH 0.927,1.979 1.302,2.188 0.375,0.208 10 false IGA 0.771,2.604 1.292,2.813 0.521,0.208 10 false GNDA 2.125,2.146 3.115,2.354 0.99,0.208 10 false RH ECU-IG 3.896,1.969 5.198,2.229 1.302,0.26 10 false from RH-IG Relay1 3.656,3.438 5.427,3.667 1.771,0.229 10 false : CAN Communication Line 0.094,3.99 2.292,4.375 2.198,0.385 10 false Yaw Rate and Acceleration Sensor 0.094,3.813 0.406,4.021 0.313,0.208 10 false N21

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor, perform acceleration sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When U0123 and/or U0126 is output together with C1234, C1472 and/or C1474, inspect and repair the trouble areas indicated by U0123 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).


PROCEDURE

1.CHECK DTC

b.

Turn the engine switch off.


c.

Start the engine.


d.

At a speed of 30 km/h (18 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.


e.

Turn the engine switch off.


f.

Turn the engine switch on (IG) again and check that no CAN communication system DTCs are output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION

B

2.CHECK YAW RATE AND ACCELERATION SENSOR INSTALLATION
a.

Turn the engine switch off.


b.

Check that the yaw rate and acceleration sensor has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR>INSTALLATION).

OK:

The yaw rate and acceleration sensor is tightened to the specified torque.

The yaw rate and acceleration sensor is not tilted.




OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

INSTALL YAW RATE AND ACCELERATION SENSOR CORRECTLY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U189709E01
0.161,0.178 0.603,0.390 0.442,0.211 10 *a 0.321,1.142 0.604,1.298 0.283,0.156 10 N21 1.966,1.881 2.248,2.037 0.283,0.156 10 IGA 2.023,1.169 2.068,1.828 false

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the N21 yaw rate and acceleration sensor connector.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N21-1 (IGA) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)



OK

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
U189710E01
0.161,0.178 0.603,0.390 0.442,0.211 10 *a 0.321,1.142 0.604,1.298 0.283,0.156 10 N21 0.911,1.847 1.416,2.002 0.505,0.156 10 GNDA 1.221,1.41 1.139,1.817 false

Turn the engine switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-4 (GNDA) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor)

HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)