Home › Vehicle Interior › ENGINE IMMOBILISER › ENGINE IMMOBILISER SYSTEM
RM24M0E _58 Vehicle Interior _059586 ENGINE IMMOBILISER _0292196 ENGINE IMMOBILISER SYSTEM C

ENGINE IMMOBILISER  ENGINE IMMOBILISER SYSTEM  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

If the communication line (EFIO - IMI) to the ID code box (immobiliser code ECU) is stuck on HI output, the ECM outputs this DTC.

DTC Code DTC Detection Condition Trouble Area
B279A When communication line (EFIO - IMI) between ECM and ID code box (immobiliser code ECU) is stuck on HI output.
·

Wire harness or connector

·

ID code box (Immobiliser code ECU)

·

ECM



WIRING DIAGRAM

B203372E78
0.796,2.122 1.130,2.262 0.334,0.140 10 ECM 0.796,1.968 1.030,2.107 0.234,0.140 10 A7 5.729,1.239 6.079,1.379 0.350,0.140 10 GND 1.301,0.483 1.517,0.622 0.216,0.140 10 IMI 1.591,0.399 1.768,0.538 0.177,0.140 10 11 5.546,1.151 5.644,1.290 0.097,0.140 10 8 5.387,2.071 6.911,2.391 1.524,0.320 10 ID Code Box (Immobiliser Code ECU) 5.387,1.906 5.668,2.051 0.281,0.145 10 G20 5.729,0.483 6.076,0.628 0.347,0.145 10 EFIO 5.547,0.399 5.644,0.544 0.097,0.145 10 6

CAUTION / NOTICE / HINT

NOTICE:
·

If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID.

·

If the ECM is replaced, register the ECU communication ID.



PROCEDURE

1.CHECK DTC OUTPUT

b.

Recheck for DTCs (See page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

HINT:

If any DTCs other than DTC B279A are output, troubleshoot those DTCs first.


Result:
Result Proceed to
DTC B279A is output A
DTC B279A and other DTCs are output B




A

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)

B

2.CHECK HARNESS AND CONNECTOR (ID CODE BOX - ECM)
a.

Disconnect the G20 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A7 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-6 (EFIO) - A7-11 (IMI) Always Below 1 Ω
G20-6 (EFIO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G20-6 (EFIO) - Body ground Always Below 1 V




OK

3.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (WAVEFORM)
a.

Reconnect the G20 ID code box (immobiliser code ECU) connector.


b.

Reconnect the A7 ECM connector.


c.

Using an oscilloscope, check that the waveform.

U188897E01
3.232,0.718 4.380,0.866 1.148,0.148 10 Normal Waveform 3.994,1.682 4.339,1.834 0.345,0.152 10 GND 6.578,1.253 6.756,1.405 0.178,0.152 10 HI 6.578,1.661 6.923,1.813 0.345,0.152 10 LOW 0.055,0.052 4.817,0.199 4.762,0.147 10 Component with harness connected: (ID Code Box (Immobiliser Code ECU)) 1.673,0.913 1.957,1.049 0.284,0.136 10 G15 1.82,2.304 2.170,2.443 0.350,0.139 10 EFIO 0.601,2.304 0.931,2.443 0.330,0.139 10 GND 1.542,1.777 1.542,2.371 1.542,2.371 1.799,2.371 false 1.196,1.777 1.196,2.371 1.196,2.371 0.94,2.371 false

Waveform (Reference):
Item Content
Terminal No. (Symbol) G15-6 (EFIO) - G15-8 (GND)
Tool Setting 5 V/DIV., 50 msec./DIV.
Condition Engine switch on (IG)


OK:

Waveform is output normally (see illustration).


Result:
Result Proceed to
NG A
OK (for 2GR-FE) B
OK (for 2AZ-FE) C




A

4.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

B

C

4.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
a.

Replace the ID code box (immobiliser code ECU).



NEXT

5.ECU CODE REGISTRATION
5.ECU CODE REGISTRATION
a.

Register the ECU code.



NEXT

6.REGISTER ECU COMMUNICATION ID
6.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT

b.

Recheck for DTCs (See page Vehicle Interior>ENGINE IMMOBILISER>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR).

OK:

B279A output does not recur.


Result:
Result Proceed to
OK A
NG (for 2GR-FE) B
NG (for 2AZ-FE) C




A

END (ID CODE BOX (IMMOBILISER CODE ECU) IS DEFECTIVE)

B

C