Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › 2014.09–2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292208 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Park / Neutral Position Switch Circuit  


DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly.

WIRING DIAGRAM

for Type A


E256016E06
2.771,1.844 3.073,2.021 0.302,0.177 10 false D4 2.771,2.021 4.094,2.354 1.323,0.333 10 false Park/Neutral Position Switch Assembly 5.271,1.802 5.583,1.979 0.313,0.177 10 false G23 5.271,1.969 6.802,2.302 1.531,0.333 10 false Clearance Warning ECU Assembly 5.365,1.313 5.542,1.49 0.177,0.177 10 false 13 2.906,0.927 3.115,1.104 0.208,0.177 10 false RB 3.75,1.313 3.948,1.49 0.198,0.177 10 false RL 1.375,1.219 2.333,1.552 0.958,0.333 10 false GAUGE NO. 2 5.438,0.51 5.531,0.688 0.094,0.177 10 false 1 3.74,0.521 3.948,0.698 0.208,0.177 10 false PL 5.604,1.427 5.802,1.604 0.198,0.177 10 false RL 5.604,0.625 5.813,0.802 0.208,0.177 10 false PL 2.365,0.729 2.615,0.906 0.25,0.177 10 false 2*1 2.365,0.917 2.813,1.094 0.448,0.177 10 false 1*2, *3 4,0.333 4.25,0.51 0.25,0.177 10 false 6*1 4,0.521 4.448,0.698 0.448,0.177 10 false 3*2, *3 4,1.135 4.25,1.313 0.25,0.177 10 false 1*1 4,1.313 4.448,1.49 0.448,0.177 10 false 2*2, *3 1.5,1.729 2.438,2.031 0.938,0.302 10 false *1: for U241E 1.5,2.052 2.385,2.354 0.885,0.302 10 false *2: for U660E 1.5,2.354 2.302,2.656 0.802,0.302 10 false *3: for K112 0.073,1.719 1.313,2.052 1.24,0.333 10 false from LH-IG Relay 1


for Type B


E256016E04
2.774,1.839 3.079,2.014 0.306,0.174 10 D4 2.774,1.998 4.097,2.330 1.324,0.332 10 Park/Neutral Position Switch Assembly 5.271,1.839 5.891,2.014 0.620,0.174 10 G108 5.271,1.998 6.807,2.330 1.536,0.332 10 Clearance Warning ECU Assembly 5.36,1.317 5.534,1.492 0.174,0.174 10 21 2.91,0.92 3.123,1.094 0.213,0.174 10 RB 3.745,1.317 3.943,1.492 0.198,0.174 10 RL 1.376,1.18 2.335,1.512 0.959,0.332 10 GAUGE NO. 2 5.44,0.524 5.534,0.699 0.094,0.174 10 6 3.739,0.524 3.943,0.699 0.204,0.174 10 PL 5.607,1.405 5.805,1.579 0.198,0.174 10 RL 5.607,0.612 5.811,0.786 0.204,0.174 10 PL 2.91,0.92 3.123,1.094 0.213,0.174 10 RB 2.737,0.911 3.190,1.085 0.453,0.174 10 1 4.003,0.518 4.456,0.693 0.453,0.174 10 3 4.003,1.317 4.456,1.491 0.453,0.174 10 2 0.068,1.683 1.304,2.015 1.236,0.332 10 from LH-IG Relay 1


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for Type A A
for Type B B




A

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)

B

5.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
a.

Disconnect the G23 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G23-1 (PL) - Body ground Engine switch on (IG)
Shift lever in P
11 to 14 V
G23-1 (PL) - Body ground Engine switch on (IG)
Shift lever in any position other than P
Below 1 V
G23-13 (RL) - Body ground Engine switch on (IG)
Shift lever in R
11 to 14 V
G23-13 (RL) - Body ground Engine switch on (IG)
Shift lever in any position other than R
Below 1 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G23 clearance warning ECU assembly connector.


b.

Disconnect the D4 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for U241E
Tester Connection Condition Specified Condition
G23-1 (PL) - D4-6 (PL) Always Below 1 Ω
G23-1 (PL) - Body ground Always 10 kΩ or higher
G23-13 (RL) - D4-1 (RL) Always Below 1 Ω
G23-13 (RL) - Body ground Always 10 kΩ or higher

for U660E, for K112
Tester Connection Condition Specified Condition
G23-1 (PL) - D4-3 (PL) Always Below 1 Ω
G23-1 (PL) - Body ground Always 10 kΩ or higher
G23-13 (RL) - D4-2 (RL) Always Below 1 Ω
G23-13 (RL) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)
a.

Disconnect the D4 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for U241E
Tester Connection Condition Specified Condition
D4-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V

for U660E, for K112
Tester Connection Condition Specified Condition
D4-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V



c.

Proceed to the next step based on the check result.

Result:
Result Proceed to
NG A
OK (for U241E) B
OK (for U660E) C
OK (for K112) D




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for U241E)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for 660E)

D

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for K112)

5.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G108-6 (PL) - Body ground Engine switch on (IG)
Shift lever in P
11 to 14 V
G108-6 (PL) - Body ground Engine switch on (IG)
Shift lever in any position other than P
Below 1 V
G108-21(RL) - Body ground Engine switch on (IG)
Shift lever in R
11 to 14 V
G108-21 (RL) - Body ground Engine switch on (IG)
Shift lever in any position other than R
Below 1 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

6.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Disconnect the D4 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-6 (PL) - D4-3 (PL) Always Below 1 Ω
G108-6 (PL) - Body ground Always 10 kΩ or higher
G108-21 (RL) - D4-2 (RL) Always Below 1 Ω
G108-21 (RL) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)
a.

Disconnect the D4 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D4-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V




OK

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR