Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for LHD) › from 2016.05
RM24M0E _56 Audio / Visual / Telematics _059590 PARK ASSIST / MONITORING _0292209 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for LHD) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for LHD)  Park / Neutral Position Switch Circuit  


DESCRIPTION

This circuit sends the park/neutral position switch assembly signals to the clearance warning ECU assembly.

WIRING DIAGRAM

E256016E07
2.771,1.844 3.073,2.021 0.302,0.177 10 false D4 2.771,2.021 4.135,2.5 1.365,0.479 10 false Park/Neutral Position Switch Assembly 5.271,1.844 5.896,2.021 0.625,0.177 10 false G108 5.271,2.01 6.802,2.344 1.531,0.333 10 false Clearance Warning ECU Assembly 5.365,1.292 5.542,1.469 0.177,0.177 10 false 21 2.906,0.896 3.115,1.073 0.208,0.177 10 false RB 3.75,1.323 3.948,1.5 0.198,0.177 10 false RL 1.375,1.177 2.333,1.51 0.958,0.333 10 false GAUGE NO. 2 5.438,0.5 5.531,0.677 0.094,0.177 10 false 6 3.74,0.531 3.948,0.708 0.208,0.177 10 false PL 5.604,1.385 5.802,1.563 0.198,0.177 10 false RL 5.604,0.583 5.813,0.76 0.208,0.177 10 false PL 2.906,0.896 3.115,1.073 0.208,0.177 10 false RB 2.594,0.74 3.042,0.917 0.448,0.177 10 false 1*1 4.021,0.396 4.469,0.573 0.448,0.177 10 false 3*1 4.021,1.146 4.469,1.323 0.448,0.177 10 false 2*1 0.104,2.104 1.813,2.292 1.708,0.188 10 false *1: for K112, U660E 4.021,0.531 4.469,0.708 0.448,0.177 10 false 6*2 2.604,0.917 3.052,1.094 0.448,0.177 10 false 2*2 4.021,1.302 4.469,1.479 0.448,0.177 10 false 1*2 0.094,1.708 1.333,2.042 1.24,0.333 10 false from LH-IG Relay 1 0.115,2.427 1.823,2.615 1.708,0.188 10 false *2: for U241E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G108-6 (PL) - Body ground Engine switch on (IG)
Shift lever in P
11 to 14 V
G108-6 (PL) - Body ground Engine switch on (IG)
Shift lever in any position other than P
Below 1 V
G108-21(RL) - Body ground Engine switch on (IG)
Shift lever in R
11 to 14 V
G108-21 (RL) - Body ground Engine switch on (IG)
Shift lever in any position other than R
Below 1 V




OK

NG

2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G108 clearance warning ECU assembly connector.


b.

Disconnect the D4 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G108-6 (PL) - D4-3 (PL)*1 Always Below 1 Ω
G108-6 (PL) - D4-6 (PL)*2 Always Below 1 Ω
G108-6 (PL) - Body ground Always 10 kΩ or higher
G108-21 (RL) - D4-2 (RL)*1 Always Below 1 Ω
G108-21 (RL) - D4-1 (RL)*2 Always Below 1 Ω
G108-21 (RL) - Body ground Always 10 kΩ or higher


*1: for K112, U660E

*2: for U241E




OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY POWER SOURCE)
a.

Disconnect the D4 park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D4-1 (RB)*1 - Body ground Engine switch on (IG) 11 to 14 V
D4-2 (RB)*2 - Body ground Engine switch on (IG) 11 to 14 V


*1: for K112, U660E

*2: for U241E



c.

Proceed to the next step based on the check result.

Result:
Result Proceed to
NG A
OK (for U241E) B
OK (for U660E) C
OK (for K112) D




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for U241E)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for 660E)

D

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (for K112)