Home › Vehicle Interior › WINDOW / GLASS › WINDSHIELD GLASS
RM24M0E _58 Vehicle Interior _059592 WINDOW / GLASS _0292222 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 28800 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 75534 2.REMOVE WINDSHIELD MOULDING OUTSIDE LH

Hide 75533 3.REMOVE WINDSHIELD MOULDING OUTSIDE RH

Hide 85192 4.REMOVE FRONT WIPER ARM HEAD CAP

Hide 85222A 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85291A 6.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53867H 7.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 8.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 55781F 9.REMOVE COWL TOP VENTILATOR LOUVER

Hide 62226 10.REMOVE FRONT PILLAR GARNISH LOWER LH

Hide 62212 11.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62212 12.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 62225A 13.REMOVE FRONT PILLAR GARNISH LOWER RH

Hide 62211 14.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

Hide 62211 15.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

Hide 62314D 16.REMOVE FRONT DOOR OPENING TRIM LH

Hide 62313D 17.REMOVE FRONT DOOR OPENING TRIM RH

Hide 87810 18.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 81260A 19.REMOVE MAP LIGHT ASSEMBLY

Hide 74320 20.REMOVE VISOR ASSEMBLY LH

Hide 74310 21.REMOVE VISOR ASSEMBLY RH

Hide 74612 23.REMOVE ASSIST GRIP COVER

Hide 74603 24.REMOVE ASSIST GRIP SUB-ASSEMBLY FRONT

Hide 63310 25.REMOVE ROOF HEADLINING ASSEMBLY

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining.


a.

Partially remove the roof headlining (See page Vehicle Interior>INTERIOR>ROOF HEADLINING>REMOVAL).


Hide 56153C 26.REMOVE FRONT WINDOW MOULDING INNER CENTER

B144555E01
2.352,1.381 3.180,1.595 0.828,0.215 10 Vehicle Body 1.565,0.501 1.820,0.702 0.255,0.201 10 Cut 2.192,0.16 2.782,0.361 0.590,0.201 10 Moulding 0.18,1.501 1.276,1.702 1.096,0.201 10 Windshield Glass 1.982,1.034 2.117,0.269 false 0.904,1.094 0.82,1.509 false 2.117,1.231 2.318,1.5 false

a.

Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 56111 27.REMOVE WINDSHIELD GLASS

B460028E01
2.375,0.99 2.375,0.125 2.375,0.125 2.177,0.125 false 0.615,1.938 0.615,1.042 0.615,1.042 1.052,1.042 false 2.542,3.115 0.885,3.115 0.885,3.115 0.885,2.719 false 1.698,3.208 1.698,3.115 false 2.542,3.115 2.542,2.708 false 2.01,4.01 2.01,3.74 2.01,3.74 1.76,3.74 false 1.25,0.052 2.177,0.333 0.927,0.281 10 false Plastic Sheet 0.188,1.958 1.531,2.208 1.344,0.25 10 false Protective Tape 1.479,3.219 2.083,3.469 0.604,0.25 10 false Stopper 1.01,3.646 1.844,3.896 0.833,0.25 10 false Piano Wire

a.

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


b.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


c.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




d.
B106095E03
0.656,1.712 1.360,1.913 0.704,0.201 10 Matchmark 1.647,1.509 1.089,1.741 1.089,1.741 1.656,1.199 false

Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if not reusing the glass.



e.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



f.

Disengage the stoppers.


g.

Using suction cups, remove the glass.


Hide 56111 28.CLEAN WINDSHIELD GLASS

B106080

a.

Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.


b.

Clean the outer edges of the glass with a non-residue solvent.

NOTICE:
Do not touch the glass surface after cleaning it.

Even if using new glass, clean it with a non-residue solvent.



Hide 58307 29.CLEAN VEHICLE BODY

B106081E49
0.417,1.375 0.417,0.396 false 2.198,1.479 2.198,0.406 false 0.896,1.521 0.979,1.698 false 2.073,1.771 1.813,1.823 false 0.146,0.177 0.844,0.375 0.698,0.198 10 false Adhesive 1.958,0.156 2.656,0.354 0.698,0.198 10 false Adhesive 0.844,1.729 1.865,1.958 1.021,0.229 10 false Vehicle Body

a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.